PFT RITMO M - Page 2

To Next Page

To Previous Page

2016-02-17

P.O. Box no. 60 97343 Iphofen

Einersheimer Straße 53 97346 Iphofen

Germany

Phone +49 9323 31-760

Fax +49 9323 31-770

Technical hotline +49 9323 31-1818

info@pft-iphofen.de

www.pft.eu

Main Page

Default Chapter3
- Table of Contents3
1 EC Declaration of Conformity6
2 Examination7
- Examination by Machine Operator7
- Periodic Inspection7
3 General Information7
- Information Regarding the Operating Manual7
- Keep the Manual for Future Reference8
- Division8
- Spare Parts Lists8
4 Technical Data9
- General Information9
- Electrical Specifications RITMO L9
- Electrical Specifications RITMO M10
- Power Values RITMO L10
- Power Values RITMO M10
- EMV Examination11
- Operating Conditions11
- Power Connection Water11
- Sound Power Level11
- Vibrations11
5 Dimension Sheet12
- Name Plate12
- Quality Control Sticker12
6 Assembly RITMO L13
- Overview RITMO L13
- Rear View RITMO L14
- Rear View RITMO M14
7 Assembly Units RITMO15
- Mixing Tube with Material Container15
- Undercarriage with Compressor and Control Cabinet15
8 Description of Assemblies16
- Overview of the Control Cabinet RITMOL16
- Overview of the Control Cabinet RITMOM16
- Overview Air Compressor DT4.817
- Overview Water Fitting RITMO L / RITMO M17
9 Connections RITMO L / RITMO M18
- Water and Air Connections18
- Connection Mortar Hose18
10 Operating Modes18
- Selector Switch Pump Motor18
- Selector Switch Water18
11 Accessories19
12 Parts from the Accessories Pack19
13 Intended Use Control Panel20
- Intended Purpose Control Panel20
- Intended Purpose Solenoid Valve20
- Intended Purpose Flow Meter20
14 Intended Use Air Compressor21
- Intended Purpose Air Compressor21
- Safety Systems Air Compressor22
- General Positioning of the Air Compressor22
- Hot Surface of the Air Compressor22
15 Description PFT Booster Pump (Accessory)23
- Scope of Application Booster Pump23
- Intended Use23
16 Preparation Booster Pump (Accessory)24
17 Initial Start-Up, Fill Pump24
- Start-Up Booster Pump24
18 Brief Description25
19 Material26
- Ritmo L26
  - Ritmo M26
20 Mortar Pressure Gauge27
21 Safety Rules27
22 Transport, Packing and Storage27
- Safety Instructions for Transport27
- Tighten the Nut before Beginning the Transport28
- Transport Inspection28
- Transport in Individual Parts29
- Transport with Passenger Car29
- Transport of Already Running Machine29
23 Packaging30
24 Operation30
- Safety30
25 Preparing the Machine31
- Connecting the Power Supply 230 V32
- Connecting the Water Supply32
- Connection of Water from Water Tank33
26 Switching on RITMO L34
- Putting RITMO L into Operation34
- Presetting the Water Flow Rate34
27 Switching on RITMO M35
- Putting RITMO M into Operation35
- Presetting the Water Flow Rate35
28 Mortar Pressure Gauge36
- Hazardous Dusts36
29 Feeding Dry Material to the Machine36
30 Monitoring the Machine37
31 Putting the Machine into Operation37
- Check Consistency of Mortar37
- Start RITMO L in "Flying Mode37
- Start RITMO M in "Flying Mode38
32 Potentiometer38
33 Mortar Hoses39
- Prepare Mortar Hoses39
- Connect Mortar Hose39
34 Compressed Air Supply40
- Connect and Fix the Air40
- Connecting the Spraying Gun40
- Switch on Air Compressor40
- Switching on Vibrating Unit (RITMO L)40
35 Apply Mortar41
- Open the Air Tap at the Spraying Gun41
- Interruption of Work42
- In Case of Longer Interruption of Work/Break42
- Switch off Air Compressor43
36 Remote Control43
- Working with the Remote Control43
37 Process Pasty Material43
- Recommended Accessories for Pasty Material43
- Process Pasty Material44
38 Stopping in Case of Emergency RITMO L / RITMO M44
- Emergency-Stop Switch44
39 Action in Case of Water Outage45
40 Action in Case of Power Cut45
- Main Switch to Position "045
41 Work on Troubleshooting47
- Reaction in the Event of Faults47
- Fault Displays48
- Faults48
- Safety48
- Table of Faults48
- Table of Faults49
42 Conveyor Stands Still / Clogging51
- Removal of Clogging in Hoses / Signs for Clogging51
- Causes for Clogging51
- Earlier Damage to the Mortar Hose52
43 Removal of Clogging in Hoses52
- Run the Pump Motor in the Backward Mode52
- Blockage Cannot be Cleared53
- Switch Machine Back on after Blockage Has Been Cleared RITMO L54
- Switch Machine Back on after Blockage Has Been Cleared RITMOM54
44 End of Work / Cleaning55
- Switching off Power Supplies55
- Check Mortar Pressure RITMO L55
- Check Mortar Pressure RITMO M56
- Cleaning RITMO56
- Clean Mortar Hose57
- Remove the Water Hose57
- Cleaning the Mixing Tube58
- Insert the Mixing Tube Cleaner58
- Cleaning Mixing Tube RITMO L59
- Cleaning Mixing Tube RITMO M59
- Cleaning Rubber Mixing Section60
- Insert Agitator60
- Clean the Hopper60
45 Changing the Pump / Cleaning the Pump61
- Place the Machine on the Back Side61
46 Switching off RITMO L61
47 Switching off RITMO M61
48 Measures in Case of Risk of Frost62
- Blow Dry Water Fitting63
- Blow Dry Water Fitting RITMO L63
- Blow Dry Water Fitting RITMO M63
49 Maintenance63
- Safety63
- Remove Connection Cable64
- Environmental Protection65
- Maintenance Plan65
50 Maintenance Work65
- Strainer Screen65
- Pressure Reducing Valve66
- Check Pressure Switch66
- Pressure Switch Water66
- Pressure Switch Compressor66
- Air Compressor Slider Control / Air Filter Cleaning67
- Actions after Completed Maintenance68
51 Disassembly69
- Safety69
- Disassembly70
52 Disposal70
53 Index72
54 Notes75

PFT RITMO M - Page 2

Table of Contents

Related product manuals