How to fix noise artifacts on ECG signal on Philips Voice Recorder?
If the Philips Voice Recorder displays 'Noise artifacts on ECG signal', ensure the patient’s skin is prepared properly. Check that the electrodes are correctly applied and the leads are making good contact with the electrodes. Also, make sure the patient cable (lead set) is properly connected to the electrodes. If the issue persists, replace the lead set.
What to do if my Philips DigiTrak XT Voice Recorder shows 'No Lead Connected message'?
If your Philips Voice Recorder displays a 'No Lead Connected message', ensure the patient’s skin has been correctly prepared. Verify that the electrodes are properly applied, and the leads are making good contact with the electrodes. Also, ensure the patient cable (lead set) is connected. If the problem continues, try replacing the lead set.
What does 'Leads Error' mean on a Philips DigiTrak XT and how can I fix it?
If the Philips Voice Recorder displays a 'Leads Error', make sure you have prepared the patient’s skin correctly. Check that the electrodes are properly applied and that the leads are making good contact with the electrodes. Also, ensure the patient cable (lead set) is connected properly. If the error persists, replace the lead set.
How to troubleshoot a Philips Voice Recorder that has no display or does not power on?
If your Philips Voice Recorder isn't displaying anything or won't turn on, first, ensure any previous ECG recording has been downloaded to the Holter application. Then, check that the battery is inserted with the correct polarity. If it still doesn't work, install a new 1.5V AAA battery. Finally, ensure the patient cable (lead set) is connected and press Enter.
What causes 'Self Test Error 52. Stuck Key. Reboot' on a Philips Voice Recorder?
If the Philips Voice Recorder displays the message 'Self Test Error 52. Stuck Key. Reboot', it might be because a key was pressed while inserting the battery. Try reinserting the battery, making sure you are not pressing any keys on the recorder. If the message continues to appear, call for service.
Why my Philips Voice Recorder does not run as long as expected?
If the Philips Voice Recorder does not run as long as expected, check the Record time in the Settings screen. Ensure a fresh alkaline battery is used for 24 or 48 hour recordings, or a fresh lithium battery is used for 96 or 168 hour recordings.
What to do if my Philips DigiTrak XT Voice Recorder indicates a low battery?
If your Philips Voice Recorder shows a 'Low battery' message, install a new battery. Also, inspect the battery compartment and clean the contacts if necessary.
What does 'Defective Card message' mean on a Philips DigiTrak XT Voice Recorder?
If the Philips Voice Recorder shows a 'Defective Card message', remove and reinsert the battery. Note that restarting the recorder will erase all patient and ECG information from the memory card, and it cannot be recovered. If the message continues to appear, call for service.
Why doesn't the battery of my Philips DigiTrak XT Voice Recorder last 24 or 48 hours?
If the Philips Voice Recorder battery does not last 24 or 48 hours, make sure a new alkaline battery is being used. Do not use rechargeable batteries.
Why doesn't the battery of my Philips DigiTrak XT last 96 or 168 hours?
If the Philips Voice Recorder battery does not last 96 or 168 hours, ensure a new lithium battery is being used. Avoid using rechargeable batteries.
The DigiTrak XT Holter recorder is intended for patients requiring ambulatory monitoring.
Explanation of symbols used on the DigiTrak XT recorder labels and documentation.
Important safety, material, and operational guidelines for using the DigiTrak XT recorder.
Details system requirements and how to access product documentation.
Overview of the DigiTrak XT recorder's buttons, connections, and physical layout.
Description of recorder screens, menus, and how to navigate them.
Covers belt clip, date/time, connecting to dock, patient prep, lead checks, and starting recording.
Information on maintaining and cleaning the DigiTrak XT recorder.
Guidance for resolving common issues, errors, and contacting service.
List of approved supplies, parts, and detailed technical specifications of the recorder.
General| Sampling Rate | 8 kHz |
|---|---|
| Recording Format | WAV |
| Microphone Type | Built-in omnidirectional microphone |
| Playback Options | Built-in speaker, headphone jack |
| Connectivity | USB |
To Next Page