What to do if my Philips Selecon PL1 has no light output?
If your Philips Lighting Equipment isn't emitting light, ensure the unit is set to the correct preset. If it is controlled via DMX, the DMX command might be set to 0 intensity, in which case you should adjust the intensity to a higher level.
What to do if my Philips Lighting Equipment LED is getting dimmer?
If the LED on your Philips Lighting Equipment is getting dimmer, it could be due to an over-temperature condition. The luminaire will reduce power to the LED if it's operating over the specified temperature. Also, check if the fan is operating correctly. Listen for fan operation or adjust settings to increase fan speed. On luminaires with a display, check the system status menu for the status of fans and LED operation.
What to do if my Philips Lighting Equipment is not detecting DMX data?
If your Philips Lighting Equipment isn't detecting DMX data, try these steps: * Disconnect and reconnect the DMX input cable. * Check the menu settings to ensure the unit is set to be controlled by DMX. * Check all DMX connections at both the control source and the luminaire. * Inspect the DMX data cable for proper wiring.
Why does my Philips Selecon PL1 have no power?
If your Philips Lighting Equipment has no power, there could be a few reasons: * The circuit may not be energized, so verify the circuit breaker is turned on. * The unit might not be plugged in, so ensure the A/C cable is connected to a power source. * The power cable could be wired incorrectly, so verify the power cable and connector are wired correctly.
What to do if my Philips Selecon PL1 Lighting Equipment is not responding to the IR remote?
If your Philips Lighting Equipment isn't responding to the IR remote, try the following: * Reselect the luminaire by repeating the luminaire selection step. * Make sure the batteries in the remote are good by trying fresh, fully charged batteries. * Ensure that IR is enabled in the fixture menu. * Make sure the IR remote is pointing at the IR window on the luminaire and that there is nothing obstructing the path between the remote and the window. * Clean the luminaire IR window.
How to unlock local programming on Philips Lighting Equipment?
If you're having trouble with local programming on your Philips Lighting Equipment, it could be due to password protection being enabled. Input the correct password to allow local programming and adjustments. Alternatively, the unit might be controlled by DMX; disconnect the input cables to check.
Outlines essential safety precautions and warnings for operating electrical equipment.
Provides contact information and publication details for DMX512 control systems.
Details the warranty terms and conditions for Philips Selecon luminaires.
Explains the manual's content and provides guidance on its use and reference.
Lists and describes various PL1 LED Luminaire models with their part numbers.
Details the PL1 LED Luminaire Handheld IR Preset Programmer.
Lists barndoors and filter holders available as accessories.
Lists specific DMX512 cables for connecting PL1 LED Luminaires.
Lists tools, such as Allen wrench sets, required for luminaire maintenance.
Lists connector types for North American models.
Identifies and illustrates the physical parts of the PL1 LED Luminaire.
Specifies the voltage and current requirements for the PL1 LED Luminaire.
Provides instructions and wiring diagrams for connecting power to the luminaire.
Details how to connect the luminaire to a DMX512 control network.
Guides users through the various mounting options and procedures for the luminaire.
Explains how to adjust the pan and tilt of the luminaire head.
Covers using the LCD display, buttons, and menu system for control and settings.
Details how to manage security levels and set/use passwords for fixture access.
Explains how to create, save, and manage presets for the luminaire's output.
Describes DMX channel mapping and control values for 16-bit DMX512 operation.
Details DMX channel mapping and control values for 8-bit DMX512 operation.
Explains DMX channel mapping and control values for 3-channel DMX512 operation.
Provides DMX512 console values for Warm White, Cool White, and Day Light presets.
Explains the use of timing channels for controlling parameter transitions in DMX.
Introduces the PLIIRR infrared programming remote and its capabilities.
Details the functions and buttons of the PLIIRR infrared remote control.
Provides general guidelines and materials for cleaning and maintaining the luminaire.
Details the procedure for cleaning the exterior and interior lenses of the luminaire.
Directs users to qualified personnel for service and maintenance beyond basic cleaning.
Guides users on how to install accessories like diffusers and barndoors onto the luminaire.
Provides a chart of common issues, symptoms, causes, and remedies for the luminaire.
Lists the general technical specifications for the PL1 LED Luminaire.
Provides detailed physical dimensions and diagrams of the PL1 LED Luminaire.
General| Brand | Philips |
|---|---|
| Model | Selecon PL1 Series |
| Category | Lighting Equipment |
| Language | English |
To Next Page