Phonic XP 5000 - Appendix; Dimensions

7XP 600/1000/2000/2100/3000/3100/5000/5100
English
XP5000 / 5100
Stereo Mode (both channels driven) Continuous Average Output Power Per Channel
8 ohms FTC 20Hz-20kHz 0.1% THD 1050W
4 ohms FTC 20Hz-20kHz 0.1% THD 1600W
2 ohms FTC 20Hz-20kHz 0.1% THD 2000W
8 ohms EIA 1kHz 0.1% THD 1100W
4 ohms EIA 1kHz 0.1% THD 1800W
2 ohms EIA 1kHz 1% THD 2500W
Bridge Mono Mode Continuous Average Output Power
8 ohms FTC 20Hz-20kHz 0.1% THD 3200W
8 ohms EIA 1kHz 0.1% THD 3600W
4 ohms EIA 1kHz 1% THD 5000W
All Models
Subwoofer output
Selectable subwoofer crossover at 60Hz, 90Hz, 120Hz
(XP5100 only)
Distortion (SMPTE-IM) <0.02%
Distortion (Typical) 20Hz-20kHz: 10dB below
rated power
<0.02%
Distortion (Typical) 1kHz and below: full rated
power
<0.02%
Frequency Response
20Hz-20kHz, 8 ohms, LF lter bypassed, +0/-1dB
5Hz to 50kHz, 8ohms, LF lter bypassed, +0/-3 dB
Damping Factor >250 @ 8 ohms
Noise (unweighted) 100 dB below rated output (20 Hz to 20kHz, 8 ohms load)
Input sensitivity 1.42 Vrms for 1000 watts into 8 ohms
Control Font AC power switch, Ch1 & Ch2 gain control with 41 detents
Control Rear
12-pole DIP switch featuring high pass lter on/off, high pass lter 30/50Hz, Clip Limiter
on/off control for each channel and switches for selecting Stereo, Parallel, or Bridge
Mode. Push-button circuit breaker for each channel. Slide switch for Grounding / Float-
ing (Selectable low pass lter frequency at 60Hz, 90Hz and 120Hz, XP5100 only)
Voltage Gain 41x (36dB)
Input Impedance 20k ohms balanced, 10k ohms unbalanced
Indicators
Power-On: Amber Phonic logo; Parallel: Green backlight icon; Bridged: Red backlight
icon; CLIP/LIM: Red LED;
PROTECT: Yellow LED Green LED for -10dB, -20dB and -40dB Signal Lights
Connectors Input XLR, 1/4”TRS jacks and barrier strip
Connectors Output Binding posts and speakon outputs (Ch1 speakon wired for biamp)
Cooling Continuous variable-speed fan, rear-to-front air ow
Amplier Protection
Short circuit, open circuit, thermal, ultrasonic, and RF protection. Stable into mis-
matched loads
Load Protection on/off muting, DC fault output crowbar
Output Circuitry Calss H Amplier
Power Requirements (depends on region)
100-120VAC, 220-240VAC (+/- 10%), 50/60Hz (factory congured); 120V model
requires 20 amp
Circuit Breakers two (one for each channel): 100 and 120V models: 20 amp / 230 V models: 10 amp
Dimensions (WxHxD) 482 x 150 x 400mm (19" x 5.9" x 15.7")
Weight 30.2 kg (66.6 lbs)
7