Connecting your equipment
03
39
En
• Switch the receiver into standby then connect your
USB device to the USB terminal on the front panel of
this receiver.
1
•For instructions on playing the USB device, see
Playing a USB device on page 48.
Connecting a USB device for Advanced
MCACC output
When using Full Auto MCACC (
page 43
), Auto MCACC
(
page 99
) or Acoustic Calibration EQ Professional
(
page 103
) to calibrate the reverb characteristics of your
listening room, the 3D graphs of the reverb
characteristics in your listening room (before and after
calibration) can be checked on a computer screen.
SC-
LX83 only:
Also, the speakers’ group delay characteristics
before and after calibration can be checked on 3D graphs.
The various MCACC parameters can also be checked on
the computer. MCACC data and parameters are
transferred from this receiver to a USB device and by
connecting the USB device to a computer, the data is
imported via the MCACC software in the computer.
The MCACC software to output the results is available by
contacting the Pioneer Authorized Distributor for your
area (as listed on page 142 of this manual) as well as the
instructions necessary for using it.
See the documentation provided with the Advanced
MCACC PC Display Application Software for more
information.
•For the USB device connection and operations, see
Output MCACC data on page 107
2
.
Connecting an IR receiver
If you keep your stereo components in a closed cabinet or
shelving unit, or you wish to use the sub zone remote
control in another zone, you can use an optional IR
receiver (such as a Niles or Xantech unit) to control your
system instead of the remote sensor on the front panel of
this receiver.
3
1 Connect the IR receiver sensor to the
IR IN
jack on
the rear of this receiver.
2 Connect the
IR IN
jack of another component to the
IR OUT
jack on the rear of this receiver to link it to the
IR receiver.
Please see the manual supplied with your IR receiver for
the type of cable necessary for the connection.
• If you want to link a Pioneer component to the IR
receiver, see Operating other Pioneer components
with this unit’s sensor below to connect to the
CONTROL jacks instead of the IR OUT jack.
1This receiver does not support a USB hub.
2The various parameters and the reverb characteristics data used for display on the computer are not cleared when the power is turned off (see
Output MCACC data on page 107).
PHONES
SPEAKERS
CONTROL
MULTI-ZONE
ON/OFF
MCACC
SETUP MIC
TUNER EDIT
USBHDMI 5
VIDEO CAMERA
iPod
iPhone
AUTO SURR/ALC/
STREAM DIRECT
HOME
THX
STANDARD
SURROUND
ADVANCED
SURROUND
STEREOBAND
USB mass
storage device
USB keyboard
3• Remote operation may not be possible if direct light from a strong fluorescent lamp is shining on the IR receiver remote sensor window.
• Note that other manufacturers may not use the IR terminology. Refer to the manual that came with your component to check for IR
compatibility.
• If using two remote controls (at the same time), the IR receiver’s remote sensor takes priority over the remote sensor on the front panel.
RS-232C
HDMI
ASSIGNABLE
COMPONENT VIDEO
ASSIGNABLE
MONITOR OUT
ZONE 2 OUT
IN
Y
ANTENNA
FM UNBAL 75 AM LOOP
ZONE2
OUT
ZONE3
OUT
DVD
IN
TV/SAT
IN
VIDEO
IN
DVR/
OUT
P
R
P
B
1
INBD
IN
1
IN
2
IN
3
1 4
(
DVD
)
IN
2
(
DVR/BDR
)
IN
3
(
VIDEO
)
CONTROL
CU-RF100
IR 12 V
TRIGGER
IN
IN
IN
OUT
OUT
1
2
1
2
(OUTPUT
12 V
TOTAL
150 mA MAX)
IN
4
(
OUTPUT 5 V
150 mA MAX
)
SPEAKERS
IN
IR
IN OUT
CONTROL
IR receiver
Closet or shelving unit
Non-Pioneer
component
Pioneer
component
SC-LX83_73_DLPW.book 39 ページ ２０１０年５月１９日 水曜日 午後２時７分
To Next Page
Loading...
