Pioneer SC-LX83 - Operating Other Pioneer Components with this Units Sensor; Switching Components on and off Using the 12 Volt Trigger

Connecting your equipment
03
40
En
Operating other Pioneer components
with this unit’s sensor
Many Pioneer components have SR CONTROL jacks
which can be used to link components together so that
you can use just the remote sensor of one component.
When you use a remote control, the control signal is
passed along the chain to the appropriate component.
1
Important
• Note that if you use this feature, make sure that you
also have at least one set of analog audio, video or
HDMI jacks connected to another component for
grounding purposes.
1 Decide which component you want to use the
remote sensor of.
When you want to control any component in the chain,
this is the remote sensor at which you’ll point the
corresponding remote control.
2 Connect the CONTROL OUT jack of that component
to the
CONTROL IN jack of another Pioneer component.
Use a cable with a mono mini-plug on each end for the
connection.
Continue the chain in the same way for as many
components as you have.
Switching components on and off using
the 12 volt trigger
You can connect components in your system (such as a
screen or projector) to this receiver so that they switch on
or off using 12 volt triggers when you select an input
function. However, you must specify which input
functions switch on the trigger using the The Input Setup
menu on page 45. Note that this will only work with
components that have a standby mode.
• Connect the 12 V TRIGGER jack of this receiver to
the 12 V trigger of another component.
Use a cable with a mono mini-plug on each end for the
connection.
After you’ve specified the input functions that will switch
on the trigger, you’ll be able to switch the component on
or off just by pressing the input function(s) you’ve set on
page 45.
It is also possible to have the component switch not when
the input function is switched, but when HDMI OUT is
switched. For details, see HDMI Setup on page 68.
Note
1 • If you want to control all your components using this receiver’s remote control, see Setting the remote to control other components on page 79
(SC-LX83)/page 92 (SC-LX73).
• If you have connected a remote control to the CONTROL IN jack (using a mini-plug cable), you won’t be able to control this unit using the
remote sensor.
CONTROL
IN
OUT
RS-232C
MONITOR
OUT
ZONE 2 OUT
Y
ANTENNA
FM UNBAL 75 AM LOOP
PRPB
CU-RF100
IR 12 V
TRIGGER
IN
IN
OUT
1
2
1
2
(OUTPUT
12 V
TOTAL
150 mA MAX)
(
OUTPUT 5 V
150 mA MAX
)
SPEAKERS
CONTROL
IN OUT
IN OUT
CONTROL
12 V
TRIGGER
1
2
(OUTPUT
12 V
TOTAL
150 mA MAX)
RS-232C
HDMI
ASSIGNABLE
COMPONENT VIDEO
ASSIGNABLE
MONITOR OUT
ZONE 2 OUT
IN
Y
ANTENNA
FM UNBAL 75 AM LOOP
C
D
IN
VID
E
MONITOR
OUT
ZONE2
OUT
ZONE3
OUT
DVD
IN
TV/SAT
IN
VIDEO
IN
DVR/BDR PHONO
IN
OUT IN
PRPB
1
INBD
IN
1
IN
2
IN
3
OUT 1
(
CONTROL
)
OU
T
1 4
(
DVD
)
IN
2
(
DVR/BDR
)
IN
3
(
VIDEO
)
CONTROL
CU-RF100
IR
IN
IN
IN
OUT
OUT
1
2
IN
4
(
OUTPUT 5 V
150 mA MAX
)
SPEAKERS
SIGNAL
GND
R
FRONT HEIGHT/
W
SEE INSTRUCTION
MANUAL
SELECTABLE
CAUTION:
SPEAKER IMPEDANCE
6 Ω - 16 Ω .
12 V TRIGGER
INPUT
SC-LX83_73_DLPW.book 40 ページ ２０１０年５月１９日 水曜日 午後２時７分