PR 9113 - 16 User Interface; Scrolling Help Texts in Display Line

18 Version No. V6R0
Safety Manual 9113 TEMPERATURE / mA CONVERTER
16 User interface
16.1 Scrolling help texts in display line 3
[01]
[02]
[03]
[04]
[05]
[06]
[07]
[08]
[09]
[11]
[12]
[13]
[14]
[15]
[16]
[17]
[18]
[19]
[20]
[21]
[22]
[23]
[24]
[25]
[26]
[27]
[28]
[29]
[30]
[31]
[32]
[33]
[34]
[35]
[36]
[37]
[38]
[40]
[41]
[42]
[43]
[44]
[45]
[46]
[47]
[48]
[49]
[50]
[51]
Set correct password
Enter advanced setup menu?
Select temperature input
Select current input
Select 0-20 mA input range
Select 4-20 mA input range
Select TC sensor type
Select Ni sensor type
Select Pt sensor type
Select Pt10 sensor type
Select Pt20 sensor type
Select Pt50 sensor type
Select Pt100 sensor type
Select Pt200 sensor type
Select Pt250 sensor type
Select Pt300 sensor type
Select Pt400 sensor type
Select Pt500 sensor type
Select Pt1000 sensor type
Select Ni50 sensor type
Select Ni100 sensor type
Select Ni120 sensor type
Select Ni1000 sensor type
Select TC-B sensor type
Select TC-E sensor type
Select TC-J sensor type
Select TC-K sensor type
Select TC-L sensor type
Select TC-N sensor type
Select TC-R sensor type
Select TC-S sensor type
Select TC-T sensor type
Select TC-U sensor type
Select TC-W3 sensor type
Select TC-W5 sensor type
Select TC-Lr sensor type
Select 2-wire sensor connection
Select 3-wire sensor connection
Select 4-wire sensor connection
Select Celsius as temperature unit
Select Fahrenheit as temperature unit
Select 0-20 mA output range
Select 4-20 mA output range
Select 20-0 mA output range
Select 20-4 mA output range
Select no error action - output undefined at error
Select downscale at error
Select NAMUR NE43 downscale at error
Select NAMUR NE43 upscale at error
Set temperature for analogue output low
Set temperature for analogue output high
Enable Rail status signal output?
Enter SIL setup
Enter simulation mode
Enter RAIL setup
Perform process calibration
Enter language setup
Enter password setup
Enter display setup
Perform memory operations
Load saved configuration into 9113
Save 9113 configuration in 4501
Adjust LCD contrast
Adjust LCD backlight
Write a 5-character channel TAG
Show analogue input value in display
Show analogue output value in display
Show TAG in display
Alternate shown information in display
Enable password protection?
Set new password
Select language
Select channel to calibrate
Calibrate input low to process value?
Set value for low calibration point
Calibrate input high to process value?
Set value for high calibration point
Use process calibration values?
Select channel to simulate
Set the input simulation value
Enable SIL configuration lock?
0-20 mA is not a valid output range for SIL
operation
Set Analog output response time in seconds
Select internal temperature sensor
Select CJC connector (accessory)
...is channel using process-compensated
calibration data?
Configuration SIL status (Open / Locked)
Sensor wire breakage
Sensor short circuit
Input underrange
Input overrange
Input error - check input connections and
reset power
Output error - check connections and reset
power
Flash memory error - check configuration
Invalid configuration type or version
Hardware error
CJC sensor error - check device temperature
CJC error - check CJC connector block
No communication