PROEL FLASH8A V2 User Manual

PROEL FLASH8A V2

46 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

FLASH8A V2

acve loudspeaker

FLASH8P V2

passive loudspeaker

USER MANUAL

MANUALE D'USO

BENUTZERHANDBUCH

NOTICE D'UTILISATION

MANUAL DE USO



Table of Contents

Questions and Answers:

J
Julian Barrett Jr.Aug 7, 2025
What to do if my PROEL FLASH8A V2 have no sound?
- D
  David JacobsAug 8, 2025
  If your PROEL Speakers aren't producing any sound, there are several things to check: * Is the input LEVEL control for the channel turned up? * Is the SIGNAL LED illuminated? * Ensure the SPEAKON cable connector is correctly inserted by turning it clockwise until it clicks. * Verify your signal level isn't too low. Also, check the signal cable, mixer, and other equipment settings and cabling. * Confirm your signal and power cables work properly, using a cable tester or replacing them with new ones.
A
Amanda SmithAug 14, 2025
How to troubleshoot no power issue in PROEL FLASH8A V2 Speakers?
- M
  Maria AustinAug 14, 2025
  If your PROEL Speakers aren't powering on, ensure the following: * The mains AC outlet is live by testing it with a tester or a lamp. * The mains plug is securely plugged into the mains AC outlet.
J
Jennifer JenkinsAug 20, 2025
What to do if PROEL FLASH8A V2 sound is distorted?
- K
  Kimberly GrayAug 20, 2025
  If the sound from your PROEL Speakers is distorted, it might be because the input signal level is too high. Try turning down your level controls to resolve this.
J
Jordan WilliamsAug 26, 2025
Why do my PROEL Speakers have noise or hum?
- M
  Michelle LewisAug 26, 2025
  If you're experiencing noise or hum with your PROEL Speakers: * Enable the GND LIFT button on the rear panel. If the problem persists, press all GND LIFT buttons for all system's amplifiers. * Use balanced cables whenever possible. * Try plugging all audio equipment into the same AC circuit to ensure they share a common ground.
R
ramirezbarbaraAug 31, 2025
What causes different channel levels in PROEL FLASH8A V2?
- J
  Joseph BakerSep 1, 2025
  If you notice a difference in channel levels with your PROEL Speakers: * Check if you're using a balanced cable for one channel and an unbalanced one for the other, as this can cause a considerable difference. * Be sure that your loudspeaker system is fully connected and both loudspeakers have the same impedance.

PROEL FLASH8A V2 Specifications

General

Speaker Type	Active
Amplifier Type	Class D
HF Amplifier Power	40W
Woofer Size	8"
Outputs	XLR
Enclosure Material	Polypropylene
Crossover Frequency	2.5 kHz
Tweeter Size	1 inch
Inputs	XLR/Jack

Related product manuals

Preview: PROEL FLASH8A

Preview: PROEL FLASH12A-V2

PROEL FLASH12A-V2

Preview: PROEL SESSION 1 FREE

PROEL SESSION 1 FREE

Preview: PROEL NEXT

Preview: PROEL V10A

Preview: PROEL AVE10A

Preview: PROEL DIVA 12A

Preview: PROEL SMART plus

PROEL SMART plus

Preview: PROEL EIKON series

PROEL EIKON series

NEOS10P - NEOS12P - NEOS15P - NEOS115SP - NEOS118SPNEOS122P - NEOS152P - NEOS215SP -NEOS218SP