ProForm PRO 2000 User Manual (English)

Questions and Answers:

P
Patricia CarrAug 16, 2025
What to do if my ProForm PRO 2000 Treadmill power turns off during use?
- R
  Regina WilsonAug 16, 2025
  If your ProForm Treadmill's power turns off during use, check the power switch and if it has tripped, wait five minutes before pressing it back in. Ensure the power cord is securely plugged in; if it is, unplug it, wait five minutes, then plug it back in. Also, try removing and reinserting the key from the console. If the issue persists, consult the front cover of this manual.
L
Laura PorterAug 19, 2025
Why ProForm PRO 2000 power does not turn on?
- J
  james18Aug 19, 2025
  If the power on your ProForm Treadmill does not turn on, verify that the power cord is connected to a properly earthed outlet. If you need to use an extension cord, make sure it is a 3-conductor, 14-gauge (2 mm2) cord no longer than 5 ft (1.5 m). After plugging in the power cord, ensure the key is correctly inserted into the console. Check the power switch on the treadmill frame; if it's protruding, wait five minutes, then press it back in to reset it.
B
bschmidtAug 22, 2025
Why does the ProForm PRO 2000 power not turn on?
- V
  Vanessa HarrisAug 22, 2025
  First, ensure the power cord is plugged into a surge suppressor that meets the specifications and that the surge suppressor is plugged into a properly grounded outlet. Then, confirm that the key is properly inserted into the console. Finally, inspect the power switch on the treadmill frame; if it's tripped, wait five minutes before resetting it.
J
Jessica RangelAug 26, 2025
How to fix ProForm PRO 2000 console when displays do not function properly?
- T
  Tiffany BrownAug 26, 2025
  If the displays of your ProForm Treadmill console are not functioning properly, try resetting the console to its factory default settings. To do this, first, turn the power switch off. Then, find the reset opening on the console. Use a bent paper clip to press and hold the reset button inside the opening while someone else turns the power switch back on. Keep holding the reset button until the console turns on, completing the reset operation, after which the console should turn off and then back on. If it doesn't, use the power switch to turn the treadmill off and then on again. Once the console turns on, check for firmware updates. It may take a few minutes for the console to be ready for use.
C
Christopher BrandtAug 28, 2025
What to do if ProForm PRO 2000 Treadmill walking belt slips when walked on?
- L
  larrymorrisAug 28, 2025
  If the walking belt on your ProForm Treadmill slips when walked on, first remove the key and unplug the power cord. Then, using the hex key, turn both idler roller screws clockwise by 1/4 of a turn. When the walking belt is correctly tightened, you should be able to lift each edge of the walking belt 2 to 3 inches (5 to 7 cm) off the walking platform. Be careful to keep the walking belt centered. Plug the power cord back in, insert the key, and walk on the treadmill for a few minutes. Repeat until the walking belt is properly tightened.
D
Dr. Edward FrancisAug 31, 2025
How to center ProForm PRO 2000 walking belt?
- M
  Michael HubbardAug 31, 2025
  If the walking belt on your ProForm Treadmill is not centered between the foot rails: * If it has shifted to the left, use the hex key to turn the left idler roller screw clockwise 1/2 of a turn. * If it has shifted to the right, turn the left idler roller screw counterclockwise 1/2 of a turn. Be careful not to overtighten the walking belt. Then, plug in the power cord, insert the key, and walk on the treadmill for a few minutes. Repeat until the walking belt is centered.
M
Matthew ColemanSep 3, 2025
How to recalibrate the incline on a ProForm Treadmill?
- J
  John ToddSep 3, 2025
  To recalibrate the incline system, hold down the Stop button and the Speed increase button, insert the key into the console, and then release the Stop button and the Speed increase button. Next, press the Stop button and then press the Incline increase or decrease button. The treadmill will automatically rise to the maximum incline level and then return to the minimum level. If the incline system does not begin calibrating, press the Stop button again, and then press the Incline increase or decrease button again. When the incline system is calibrated, remove the key from the console.
V
Vanessa AdamsSep 6, 2025
What to do if the ProForm Treadmill walking belt slows down when walked on?
- D
  darlenerogersSep 6, 2025
  This issue might happen if the walking belt is overtightened, which can decrease treadmill performance and potentially damage the belt. To resolve this, remove the key and unplug the power cord. Use the hex key to turn both idler roller screws counterclockwise by 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each edge of the walking belt 2 to 3 inches off the walking platform. Ensure the belt remains centered. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat these steps until the walking belt is properly tightened.
D
daisy08Sep 9, 2025
What to do if the power turns off during ProForm PRO 2000 Treadmill use?
- J
  Jeffrey DavisSep 9, 2025
  First, check the power switch and if it has tripped, wait five minutes before pressing it back in. Next, ensure the power cord is securely plugged in; if it is, unplug it, wait five minutes, and plug it back in. Also, try removing and reinserting the key from the console. If the treadmill still won't run after these steps, further assistance is needed.

ProForm PRO 2000 Specifications

General

Speed Range	0-12 MPH
Running Surface	20" x 60"
Weight Capacity	300 lbs
Display	7" Backlit LCD
Folding	Yes
Heart Rate Monitoring	EKG Grip Pulse
Bluetooth	Yes
Cooling Fan	CoolAire Fan
Audio	Dual 2" Speakers
Incline Range	-3% Decline to 12% Incline Digital Control