What does it mean if sections must be specified in left-to-right order in Raven Control Systems?
This message indicates that the sections are not configured sequentially in a left-to-right order. Configure the sections in a left-to-right order. See the Boom and Implement Setup section on page 169 for more information on configuring sections.
How to fix Raven Viper Pro when dates and time are incorrect?
If the dates and time are incorrect on your Raven Control Systems, it could be due to the following reasons: * No GPS signal. * No GPS RMC or ZDA string. * Incorrect time zone selected. To fix this, ensure that the GPS receiver is operating properly and that there is a green 'thumbs-up' icon displayed in the GPS section of the main screen. Also, check the GPS receiver to make sure the RMC or ZDA string is selected and verify the time zone selected in the Menu/Setup/Local/Time Zone section.
Why are CAN nodes not detected in my Raven Control Systems?
If CAN nodes are not being detected, the possible causes are: * No power to CAN nodes. * Weak or dirty power to the CAN nodes. * Water in CAN nodes. * Corrosion in CAN connections. * Broken cable to node. * Low power voltage. Verify that there is 12 volt power and ground to the CAN node's logic power. Make sure that the 12 volt power to the CAN node is coming from the switch relay that is connected to the battery. Prevent water and moisture from building up in the nodes. Disconnect and clean the CAN connections. Repair or replace the cable and verify at least +10VDC at the node.
What to do if the Raven Control Systems touch screen does not respond to touch?
If the touch screen is unresponsive, it might be because the area you're touching doesn't include a selectable function, or the system is busy processing a previous request. Touch an area of the screen that contains a selectable function. Wait for the system to finish processing previous requests.
Why is there a gap or overlap between sections in my Raven Control Systems?
A gap or overlap between sections can occur due to improper values entered into either section widths and/or the left/right values for individual sections, or section select functions are not properly configured. Check the section setup values entered for Left/Right, and check the sections set up for this product. Set up sections sequentially from left-to-right. Left/Right value is measured from the center of the section. Section select must specify individual sections for individual products if a gap or overlap is detected.
Why does only one prescription map load on my Raven Control Systems?
If only one prescription map loads, it is likely because a multi-product VRA registration is not available. Purchase a multi-product registration from a local Raven dealer.
Why does the prescription map not display properly on my Raven Viper Pro Control Systems?
If the prescription map does not display properly, it could be due to the wrong datum type. Use WGS-84 decimal degrees when creating an Rx map.
Why doesn't the boom number turn green when turned on in Raven Viper Pro?
If the boom number does not turn green when turned on, it could be because the boom is not set up properly, nodes are not completely programmed, or the boom is disconnected. Check the boom setup from the Setup menu. Check node calibration and ensure all calibration is completed. Check the connection and wiring to the boom.
Why will streetmaps not load on my Raven Viper Pro Control Systems?
If streetmaps will not load, it could be due to several reasons: * The streetmaps files are not located in the streetmaps folder. * Streetmaps are located in a sub-folder in the Streetmaps folder. * Streetmaps are not in the correct format. * Too many streetmaps files in the Streetmaps folder. Move the streetmaps files to the Streetmaps folder on the disk. Move the streetmaps to the Streetmaps root folder. Save the streetmap files in the shapefile format. Limit the number of county streetmap files in the Streetmap folder.
Why are boom numbers gray on my Raven Viper Pro?
If the boom numbers are gray, it could be because the boom switches are turned off, AccuBoom is enabled but the machine is not moving, or the CAN is disconnected. Turn the boom and master switch on. Move the machine out of the applied zone. See the CAN Troubleshooting section on page 212.
General| Brand | Raven |
|---|---|
| Model | Viper Pro |
| Category | Control Systems |
| Language | English |
To Next Page
