What does it mean if sections must be specified in left-to-right order in Raven Control Systems?
This message indicates that the sections are not configured sequentially in a left-to-right order. Configure the sections in a left-to-right order. See the Boom and Implement Setup section on page 169 for more information on configuring sections.
How to fix Raven Viper Pro when dates and time are incorrect?
If the dates and time are incorrect on your Raven Control Systems, it could be due to the following reasons: * No GPS signal. * No GPS RMC or ZDA string. * Incorrect time zone selected. To fix this, ensure that the GPS receiver is operating properly and that there is a green 'thumbs-up' icon displayed in the GPS section of the main screen. Also, check the GPS receiver to make sure the RMC or ZDA string is selected and verify the time zone selected in the Menu/Setup/Local/Time Zone section.
Why are CAN nodes not detected in my Raven Control Systems?
If CAN nodes are not being detected, the possible causes are: * No power to CAN nodes. * Weak or dirty power to the CAN nodes. * Water in CAN nodes. * Corrosion in CAN connections. * Broken cable to node. * Low power voltage. Verify that there is 12 volt power and ground to the CAN node's logic power. Make sure that the 12 volt power to the CAN node is coming from the switch relay that is connected to the battery. Prevent water and moisture from building up in the nodes. Disconnect and clean the CAN connections. Repair or replace the cable and verify at least +10VDC at the node.
What does No Rx file chosen for this product mean in Raven Viper Pro?
This message indicates that VRC was selected for the product during the product setup, but no Rx map was loaded. Un-select the VRC selection or load an Rx map for the product.
Why is there a red 'X' in the product control area on my Raven Viper Pro main screen?
A red 'X' in the product control area may appear due to several reasons: * The control console might not be turned on. * There could be a connection issue between the control console and the Viper Pro. * The wrong console model might be selected in the product control setup menu. * The communication port settings between the control console and the Viper Pro might be incorrect. * You might be using the wrong communications cable. * There could be a node connection issue on the CAN system. To resolve this, ensure the control console is powered on, check the connections, verify the correct console model is selected in the settings (Menu>Setup>Prod Control), confirm that the communication port settings match, and use the supplied communications cable. For CAN system issues, refe...
What does Missing Product Information mean: No Product Name Entered in Raven Viper Pro?
This message indicates that no product name has been entered. Enter at least one character for a product name.
Why does only one prescription map load on my Raven Control Systems?
If only one prescription map loads, it is likely because a multi-product VRA registration is not available. Purchase a multi-product registration from a local Raven dealer.
Why does the prescription map not display properly on my Raven Viper Pro Control Systems?
If the prescription map does not display properly, it could be due to the wrong datum type. Use WGS-84 decimal degrees when creating an Rx map.
What does No GPS mean in Raven Control Systems?
This message indicates that Viper does not detect a GPS signal. Make sure that the GPS receiver is turned on and receiving a signal. Ensure that the port setting for Viper and the GPS receiver match. Also, make sure that the required NMEA messages are turned on in the GPS receiver.
Why will streetmaps not load on my Raven Viper Pro Control Systems?
If streetmaps will not load, it could be due to several reasons: * The streetmaps files are not located in the streetmaps folder. * Streetmaps are located in a sub-folder in the Streetmaps folder. * Streetmaps are not in the correct format. * Too many streetmaps files in the Streetmaps folder. Move the streetmaps files to the Streetmaps folder on the disk. Move the streetmaps to the Streetmaps root folder. Save the streetmap files in the shapefile format. Limit the number of county streetmap files in the Streetmap folder.
Provides a step-by-step overview of the Viper Pro installation procedure.
Instructions and requirements for selecting a mounting location for the Viper Pro.
Details on the two available cable platform options for the Viper Pro field computer.
Diagram and instructions for connecting the Generation 1 cable platform.
Diagram and instructions for connecting the Generation 2 cable platform.
Procedures for powering up and initiating the Viper Pro field computer.
Ensuring proper communication with CANbus nodes for accurate product application.
Configuring essential system settings like language, time zone, and display units.
Selecting the appropriate controller setting for CANbus or serial console operation.
Configuring speed sensor settings and calibration for accurate rate adjustments.
Configuring valve settings based on product type and machine application.
Setting the target rate for product application for each control channel.
Entering the meter calibration number for liquid product flow measurement.
Calibrating dry/granular application systems using spreader constant and product density.
Programming calibration values for control valves to adjust response time.
Configuring boom and section widths for guidance and product control.
Automatic control of boom sections based on coverage or spray/no-spray zone maps.
Procedure for starting a job using AgX recommendations and pre-populated data.
Configuring job name, guidance pattern, and AccuBoom mapping modes.
Steps to begin a standard job and enter all product and job information.
Calibrating prescription maps and setting default application rates.
Information on how the Viper Pro displays and handles configured alarm conditions.
Procedures for viewing and resolving detected alarm conditions.
Selecting and using various swath patterns for guidance during a job.
Linking product tanks or bins to automatically switch for continuous application.
Configurable settings for monitoring and controlling product application via CANbus.
Configuring hardware control based on specific product nodes or booms.
Configuring communication ports for GPS, console, and auxiliary devices.
Configuring applicator boom or implement sections for monitoring or control.
Configuring AccuBoom functionality for automatic boom section control.
Setting up AccuBoom operation using spray and no-spray zones.
Determining the current status of the AutoBoom system via the Viper main screen.
Process of archiving and deleting files to maintain Viper Pro system efficiency.
Steps to prepare a USB flash drive with necessary file folders for maintenance.
Accessing flexible options for managing and maintaining files on the Viper Pro.
Uploading prescription maps from a USB flash drive via the File Maintenance screen.
Copying, moving, or deleting files from USB drives or internal memory.
Automatic process for moving report files and deleting job files from Viper Pro storage.
Transferring or deleting AgX recommendations to/from the Viper Pro.
Information on troubleshooting common issues and solutions for the Viper Pro system.
Troubleshooting common problems like power, CAN node detection, and touch screen.
Resolving issues related to lost settings, default profiles, and CAN connections.
Troubleshooting problems with streetmaps, boom display, product functions, and dates.
Resolving issues related to loading and displaying prescription (Rx) maps.
General| Brand | Raven |
|---|---|
| Model | Viper Pro |
| Category | Control Systems |
| Language | English |
To Next Page
