What to do if the activation key is not valid in Raven Viper Pro?
If the activation key is not valid, it is likely because an incorrect activation key was entered. Re-enter the Activation key. If this still does not work, contact a local Raven representative.
What does Scout file error mean in Raven Viper Pro Control Systems?
A Scout file error can occur if the scout file for one of the jobs is missing, or the file is an older version and not compatible with the current software release. Touch OK to bypass.
What does JobMap error mean in Raven Control Systems?
A JobMap error indicates that the scout file for the job is missing. Touch OK to bypass and create a scout file for the current job.
What does it mean if sections must be specified in left-to-right order in Raven Control Systems?
This message indicates that the sections are not configured sequentially in a left-to-right order. Configure the sections in a left-to-right order. See the Boom and Implement Setup section on page 169 for more information on configuring sections.
Why is there a gap or overlap between sections in my Raven Control Systems?
A gap or overlap between sections can occur due to improper values entered into either section widths and/or the left/right values for individual sections, or section select functions are not properly configured. Check the section setup values entered for Left/Right, and check the sections set up for this product. Set up sections sequentially from left-to-right. Left/Right value is measured from the center of the section. Section select must specify individual sections for individual products if a gap or overlap is detected.
General| Brand | Raven |
|---|---|
| Model | Viper Pro |
| Category | Control Systems |
| Language | English |
Provides a step-by-step overview of the Viper Pro installation procedure.
Instructions and requirements for selecting a mounting location for the Viper Pro.
Details on the two available cable platform options for the Viper Pro field computer.
Diagram and instructions for connecting the Generation 1 cable platform.
Diagram and instructions for connecting the Generation 2 cable platform.
Procedures for powering up and initiating the Viper Pro field computer.
Ensuring proper communication with CANbus nodes for accurate product application.
Configuring essential system settings like language, time zone, and display units.
Selecting the appropriate controller setting for CANbus or serial console operation.
Configuring speed sensor settings and calibration for accurate rate adjustments.
Configuring valve settings based on product type and machine application.
Setting the target rate for product application for each control channel.
Entering the meter calibration number for liquid product flow measurement.
Calibrating dry/granular application systems using spreader constant and product density.
Programming calibration values for control valves to adjust response time.
Configuring boom and section widths for guidance and product control.
Automatic control of boom sections based on coverage or spray/no-spray zone maps.
Procedure for starting a job using AgX recommendations and pre-populated data.
Configuring job name, guidance pattern, and AccuBoom mapping modes.
Steps to begin a standard job and enter all product and job information.
Calibrating prescription maps and setting default application rates.
Information on how the Viper Pro displays and handles configured alarm conditions.
Procedures for viewing and resolving detected alarm conditions.
Selecting and using various swath patterns for guidance during a job.
Linking product tanks or bins to automatically switch for continuous application.
Configurable settings for monitoring and controlling product application via CANbus.
Configuring hardware control based on specific product nodes or booms.
Configuring communication ports for GPS, console, and auxiliary devices.
Configuring applicator boom or implement sections for monitoring or control.
Configuring AccuBoom functionality for automatic boom section control.
Setting up AccuBoom operation using spray and no-spray zones.
Determining the current status of the AutoBoom system via the Viper main screen.
Process of archiving and deleting files to maintain Viper Pro system efficiency.
Steps to prepare a USB flash drive with necessary file folders for maintenance.
Accessing flexible options for managing and maintaining files on the Viper Pro.
Uploading prescription maps from a USB flash drive via the File Maintenance screen.
Copying, moving, or deleting files from USB drives or internal memory.
Automatic process for moving report files and deleting job files from Viper Pro storage.
Transferring or deleting AgX recommendations to/from the Viper Pro.
Information on troubleshooting common issues and solutions for the Viper Pro system.
Troubleshooting common problems like power, CAN node detection, and touch screen.
Resolving issues related to lost settings, default profiles, and CAN connections.
Troubleshooting problems with streetmaps, boom display, product functions, and dates.
Resolving issues related to loading and displaying prescription (Rx) maps.
To Next Page
