EasyManua.ls Logo

Reboot RBM-2100D - User Manual

Reboot RBM-2100D
22 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
- 1 -
Operation Manual
RBM-2100D MIG Welding Machine

Table of Contents

Questions and Answers

  • N
    Natasha PeckAug 6, 2025
    What to do if Reboot RBM-2100D shows no meter, fan doesn't rotate, and no welding output?
    • M
      Matthew WhiteAug 7, 2025
      If your Reboot Welding System shows nothing on the meter, the fan isn't rotating, and there's no welding output, first, ensure the power switch is turned on. Next, verify that the input cable is receiving power. If these steps don't resolve the issue, it's possible the three-phase commute bridge is damaged, or there's a malfunction in the supplementary power source on the control board, in which case you should contact dealers.
  • T
    Tina PhillipsAug 15, 2025
    How to fix Reboot RBM-2100D Welding System with meter showing, fan working, but no welding output?
    • I
      Isabel GreenAug 15, 2025
      If your Reboot Welding System's meter is showing and the fan is working normally, but there's no welding output, begin by checking all the sockets in the machine to ensure they are well-connected. Also, inspect the output terminal joint for any open circuits or poor connections. Another potential cause is a broken control cable on the torch or a damaged switch. If these checks don't resolve the issue, the control circuit may be damaged, and you should contact dealers.
  • S
    samantharamseyAug 26, 2025
    Why Reboot RBM-2100D shows abnormal indicator lights?
    • A
      Aaron MckenzieAug 26, 2025
      If your Reboot Welding System's meter is displaying, the fan is working, but the indicator lights are abnormal, it could be due to over-current protection. Try turning off the power switch and restarting the machine after the abnormal indicator light has winked. Alternatively, it may be overheating protection; in this case, wait approximately 2-3 minutes for the machine to reset without turning off the power switch. If neither of these resolves the issue, there might be a malfunction in the inverter circuit, and you should contact dealers.

Summary

Product Introduction and Specifications

Product Summary Overview

Overview of product features and technology.

Technical Specifications

Key technical specifications of the welding machine.

Included Accessories

List of accessories included with the welding machine.

Welding Machine Installation Guide

Welding Wire Installation

Step-by-step guide for installing welding wire.

Torch Components Diagram

Exploded diagram of MIG and TIG torches.

Gas Shielded Welding Setup

Instructions for MIG and LIFT TIG gas connections.

Spool Gun Installation

Procedure for installing the MIG spool gun.

Operating Instructions and Modes

Control Panel Overview

Explanation of the machine's control panel interface.

Welding Operation Procedures

Guidance on operating the welder in different modes.

Spool Gun Operation

How to connect and use the spool gun.

LIFT TIG Functionality

Instructions for using the LIFT TIG welding function.

Polarity Conversion

Connecting polarity cables for different wire types.

Troubleshooting and Error Diagnosis

Common Malfunctions and Solutions

Table of common malfunctions and their recommended solutions.

Maintenance and Daily Checks

Daily Maintenance Procedures

Routine cleaning and upkeep procedures for the welder.

Daily Inspection Checklist

Checklist for daily inspection of welding machine components.

Welding Problem Solutions

Common welding issues and their causes/solutions.

Safety Precautions and Environment

Welding Environment and Safety Rules

Guidelines for safe working environment and operational safety.

Safety Symbol Definitions

Explanation of safety symbols used in the manual.

Electromagnetic Interference

Precautions for electromagnetic interference during operation.

Welding Parameter Appendix

Square Butt Welding Parameters

Welding parameters for square butt joints.

Fillet Butt Welding Parameters

Welding parameters for fillet butt joints.

Horizontal Fillet Butt Welding

Welding parameters for horizontal fillet butt T joints.

Horizontal Fillet Welding

Welding parameters for horizontal fillet joints.

Service and Warranty Information

Warranty Terms and Conditions

Details about product warranty coverage and limitations.

Reboot RBM-2100D Specifications

General IconGeneral
Input Voltage220V
Frequency50/60 Hz
Efficiency85%
Protection ClassIP21S
Welding TypeMMA
Duty Cycle60%

Related product manuals