red lion PAXR - Troubleshooting and Parameter Summary; Troubleshooting Common Problems; Parameter Value Chart

15
* See Module 2, Exchanging Parameter Lists, for details on programming this value.
DISPLAY PARAMETER USER SETTING
FACTORY
SETTING
USr-1
USER INPUT 1
NO
USr-2
USER INPUT 2
NO
USr-3
USER INPUT 3
NO
F1
FUNCTION KEY 1
NO
F2
FUNCTION KEY 2
NO
rSt
RESET KEY
dSPrSt
Sc-F1
2nd FUNCTION KEY 1
NO
Sc-F2
2nd FUNCTION KEY 2
NO
2-FNC User Input and Function Key Parameters
3-LOC Display and Program Lockout Parameters
4-rtE Rate Input Parameters
DISPLAY PARAMETER USER SETTING
FACTORY
SETTING
SP-3
SP-4
SETPOINT 3 ACCESS LOCK-OUT
LOC
LOC
LO
rAtE
MIN DISPLAY LOCK-OUT
RATE DISPLAY LOCK-OUT
LOC
rEd
SP-1
HI
SETPOINT 1 ACCESS LOCK-OUT
MAX DISPLAY LOCK-OUT
LOC
LOC
COdE
SP-2
SECURITY CODE
SETPOINT 2 ACCESS LOCK-OUT
0
LOC
rtEINP
RATE SCALING INPUT
1000.0
rOUNd
LO-Udt
RATE DISPLAY ROUNDING
LOW UPDATE TIME
1
1.0
LOCUt
HI-Udt
MINIMUM LOW CUT OUT
HIGH UPDATE TIME
0
2.0
LO-t
rtEdSP
HI-t
rtE dP
MIN CAPTURE DELAY TIME
RATE SCALING DISPLAY
MAX CAPTURE DELAY TIME
RATE DECIMAL POINT
2.0
1000
2.0
0
DISPLAY PARAMETER USER SETTING
FACTORY
SETTING
PARAMETER VALUE CHART
Programmer ________________ Date ________
PAXR Rate Meter Meter# _____________ Security Code __________
SETPOINT 4 ACCESS LOCK-OUT
TROUBLESHOOTING
For further assistance, contact technical support at the appropriate company numbers listed.
PROBLEM REMEDIES
NO DISPLAY CHECK: Power level, power connections
PROGRAM LOCKED-OUT
CHECK: Active (lock-out) user input
ENTER: Security code requested
CERTAIN DISPLAYS ARE LOCKED OUT CHECK: Module 3 programming
INCORRECT DISPLAY VALUE
CHECK: Input wiring, DIP switch setting, input programming, input signal level,
user input jumper, lower input signal frequency
USER INPUT NOT WORKING CORRECTLY CHECK: User input wiring, user input jumper, Module 2
OUTPUT DOES NOT WORK CHECK: Corresponding plug-in card installation, output configuration, output wiring
JITTERY DISPLAY
CHECK: Wiring is per EMC installation guidelines, input signal frequency, signal quality,
scaling, update time, DIP switch setting
“! *#*#” RATE
CHECK: Lower input signal frequency, reduce rate scaling
MODULES or PARAMETERS NOT ACCESSIBLE CHECK: Corresponding plug-in card installation, related controlling parameter selected
ERROR CODE (&!! /39)
PRESS: Reset key (if unable to clear contact factory.)
0
1.00
0.00
100
0.00
100
NO
OFF
0
HI
OFF
NOr
NO
NOr
SP-4
USER SETTING
1.00
0.00
100
0.00
100
NO
OFF
HI
OFF
NOr
NO
NOr
SP-3
FACTORY
SETTING
USER SETTING
FACTORY
SETTING
0
1.00
0.00
100
0.00
100
NO
OFF
0
SETPOINT HYSTERESIS
HYS-n
HI
OFF
NOr
NO
NOr
SP-2
USER SETTING
1.00
SETPOINT TIME OUT
tOUt-n
0.00
100
SETPOINT ON DELAY
SETPOINT VALUE (B)*
tON-n
0.00
100
SETPOINT OFF DELAY
SETPOINT VALUE (A)
tOFF-n
SP-n
NO
OFF
STANDBY OPERATION
SETPOINT ACTION
Stb-n
ACt-n
HI
OFF
NOr
NO
NOr
SETPOINT BOUNDARY TYPE
SETPOINT POWER UP STATE
SETPOINT OUTPUT LOGIC
SETPOINT TRACKING
SETPOINT ANNUNCIATORS
tYP-n
SUP-n
OUt-n
trC-n
LIt-n
SP-1
FACTORY
SETTING
USER SETTING
FACTORY
SETTING
PARAMETERDISPLAY
6-SPt Setpoint (Alarm) Parameters