red lion PAXR - Display Control Functions; Setpoint Control Functions

8
!
"
$%*!&
7$!3/
!
"
$%*!&
4/
STORE DISPLAY
The meter holds (freeze) the displays configured as 6&$, as long as activated
(maintained action). Internally the maximum and minimum values continue to
update.
!
"
$,!$%#
7$!3/
!
"
$,!$%#
4/
DEACTIVATE SETPOINT MAINTAINED (LEVEL)
The meter deactivates the setpoints configured as 6&$, as long as activated
(maintained action). This action only functions with a Setpoint plug-in card
installed.
!
"
$,!$%&
7$!3/
!
"
$,!$%&
4/
DEACTIVATE SETPOINT MOMENTARY (EDGE)
When activated (momentary action), the meter deactivates the setpoints
configured as 6&$. This action only functions with a Setpoint plug-in card
installed.
!
"
$,"*#+
7$!3/
!
"
$,"*#+
4/
HOLD SETPOINT STATE
The meter holds the state of the setpoints configured as 6&$, as long as
activated (maintained action). This action only functions with a Setpoint plug-
in card installed.
!
"
"#!$%#
7$!3/
!
"
"#!$%#
4/
MAINTAINED (LEVEL) RESET AND INHIBIT
The meter performs a reset and inhibits the displays configured as 6&$, as
long as activated (maintained action).
!
"
"#!$%&
7$!3/
!
"
"#!$%&
4/
MOMENTARY (EDGE) RESET
When activated (momentary action), the meter resets the displays configured
as
6&$. (Momentary resets improve maximum input frequencies over
maintained resets.)
!
"
'("')%
7$!3/
!
"
'("')%
4/
INHIBIT
The meter inhibits the displays configured as 6&$, as long as activated
(maintained action).
NO
Minimum
LO
NO
Maximum
HI
FACTORYDESCRIPTIONDISPLAY
NO
Minimum
LO
NO
Maximum
HI
FACTORYDESCRIPTIONDISPLAY
NO
Minimum
LO
NO
Maximum
HI
FACTORYDESCRIPTIONDISPLAY
NO
Minimum
LO
NO
Maximum
HI
FACTORYDESCRIPTIONDISPLAY
DISPLAY DESCRIPTION FACTORY
SP-1
Setpoint 1
NO
SP-2
Setpoint 2
NO
SP-3
Setpoint 3
NO
SP-4
Setpoint 4
NO
NO
Setpoint 4
SP-4
NO
Setpoint 3
SP-3
NO
Setpoint 2
SP-2
NO
Setpoint 1
SP-1
FACTORYDESCRIPTIONDISPLAY
NO
Setpoint 4
SP-4
NO
Setpoint 3
SP-3
NO
Setpoint 2
SP-2
NO
Setpoint 1
SP-1
FACTORYDESCRIPTIONDISPLAY
!
"
+$,!$%
7$!3/
!
"
+$,!$%
4/
RESET DISPLAY
When activated (momentary action), the shown display is reset. This is the
factory setting for the Reset (RST) Key.
!
"
#'$%
7$!3/
!
"
#'$%
4/
EXCHANGE PARAMETER LISTS
Two lists of values are available for $,3/, $,32, $,38, and $,39. The two
lists are named #'$%3: and #'$%3). If a user input is used to select the list then
#'$%3: is selected when the user input is not active and #'$%3) is selected when
the user input is active, (maintained action). If a front panel key is used to select
the list then the list will toggle for each key press, (momentary action). The
meter will suspend ALL operations for approximately 1 msec. while the new
values are loaded. The display will only indicate which list is active when the
list is changed or when entering any Programming Mode.
To program the values for #'$%3: and #'$%3), first complete the
programming of all the parameters. Exit programming and switch to the other
list. Re-enter programming and enter the values for $,3/, $,32, $,38, $,39. If
any other parameters are changed, then the other list values must be
reprogrammed.
!
"
+$,$&#
4/
ADVANCE DISPLAY
When activated (momentary action), the display advances to the next display
that is not locked out from the Display Mode.
!
"
+$,$&#
7$!3/