To Next PageTo Next PageWhat to do if Reer EOS2 A detect an interfering emitter?
If your Reer Security Sensors detect an interfering emitter, try the following: * Reduce the range of the interfering emitter from high to low. * Swap the positions of the emitter and receiver. * Move the interfering emitter so it doesn't illuminate the receiver. * Shield the beams emitted by the interfering emitter using opaque protections.
What to do if OSSD outputs error on Reer EOS2 A?
If the OSSD outputs of your Reer Security Sensors are showing an error, first check the connections. If the problem continues, send the device to REER for repair.
What to do if Reer Security Sensors are awaiting communication Master/Slave?
If your Reer Security Sensors are awaiting Master/Slave communication, check the condition of the Master. If it's in a FAIL condition, check the type of fault. If the fault persists, send the device to ReeR laboratories for repair.
What to do if there is no feedback from external contactors on Reer EOS2 A?
If your Reer Security Sensors are not providing feedback from external contactors, check the connection of pin 4.
What to do if Reer Security Sensors have incorrect configuration?
If your Reer Security Sensors have an incorrect configuration, check the connections.
General| Type | Safety Light Curtain |
|---|---|
| Supply voltage | 24 V DC |
| Detection Principle | Infrared |
| Protection Rating | IP65 |
| Connection | M12 Connector |
| Resolution | 14 mm |
| Safety level | Type 4 |
| Output | 2 safety outputs |
| Operating Temperature | -10°C to +50°C |
| Safety Standards | EN ISO 13849-1, IEC 61496-1 |
Details the different models of the EOS2 light curtain available.
Explains system resolution, protected height, and working range.
Lists resolutions, protected heights, and model applications.
Prerequisites and general guidelines for installing the safety system.
Guidance on correct and incorrect physical placement of the light curtain.
Configuration options for Master/Slave light curtain setups.
Formulas and parameters for calculating minimum safety distances.
Precautions to prevent optical interference when using multiple systems.
How to use deflecting mirrors for U-shaped protection.
Maintaining distance from reflective surfaces to ensure proper sensing.
Instructions for mounting and aligning the emitter and receiver.
Guidance on vertical placement for 30/40mm and 50/90mm models.
Details on multibeam models and horizontal placement strategies.
Pin assignments and wiring for Emitter M12 connectors.
Pin assignments and wiring for Receiver M12 connectors.
Important considerations for using connection cables.
How to configure automatic or manual operating modes using receiver connections.
Wiring diagrams for connecting external contactors K1 and K2.
Understanding the meaning of LED indicators on the emitter and receiver.
How the light curtain performs internal self-checks for faults.
Procedure for performing periodic system tests.
Meaning of output statuses (OSSD1, OSSD2) based on curtain conditions.
Key technical parameters of the EOS2 light curtains.
Formula to calculate total response time for Master/Slave configurations.
Compliance with safety standards like IEC 61496, IEC 61508, ISO 13849.
Technical data including response time, height, PFHd, DCavg.
Technical data including response time, height, PFHd, DCavg.
Technical data including response time, height, PFHd, DCavg.
Technical data including response time, height, PFHd, DCavg.
Diagrams and measurements for EOS2 Emitter and Receiver units.
Specific dimensions and mounting details for Multibeam EOS2 models.
Procedure for verifying the light curtain's operational efficiency.
Guidelines for cleaning and maintaining the light curtain.
Interpretation of Emitter LED signals for troubleshooting.
Interpretation of Receiver LED signals for troubleshooting.
Steps to take when the system stops or exhibits incorrect behavior.
Required information when contacting REER for service.
Available safety modules and their codes.
Various connectors and cables for system extension.
Brackets, inserts, and vibration-damping supports.
Terms and conditions for the product guarantee.
Limitations of REER's liability and responsibility.
