Depending on the effect, the time parameter‘s type and interval and the adjustments according to
the beat assignment buttons -24-, will differ.
Continuously repeats a certain interval of the signal.
Time parameter value: 2 – 2000 msec
Direct bar assignment: Intervals adjustable from 125 – 2000
By turning the X parameter knob -25- the value will be changed in steps of 1. Push, hold and turn the
X parameter knob -25- and the value will be changed in steps of 100.
Y parameter dry/wet value: 0 - 100%
Produces the signal‘s continuous fading of the signal from the left to the right channel and back
again.
Time parameter value: 30 – 65000 msec
Direct bar assignment: 500/1000/2000/4000/8000/16000 msec
By turning the X parameter knob -25- the value will be changed in steps of 1. Push, hold and turn the
X parameter knob -25- and the value will be changed in steps of 100.
Y parameter dry/wet value: 0 - 100%
Doubles the signal and shifts it by a marginal value.
Time parameter value: 100 – 65000 msec
Direct bar assignment: 500/1000/2000/4000/8000/16000
By turning the X parameter knob -25- the value will be changed in steps of 1. Push, hold and turn the
X parameter knob -25- and the value will be changed in steps of 100.
Y parameter dry/wet value: 0 – 100%
With this effect you can manually control a Hipass and LowPass lter effect respectively.
Time parameter value: LowPass 0.05 – 20.2 kHz / HiPass 0.13 – 21.1 kHz
Direct bar assignment: LowPass 0.45/2.27/7.13/18.4 kHz – HiPass 1.63/5.73 kHz
By turning the Xparameter knob -25- the value will be changed in steps from 0.2 – 0.4. Push, hold
and turn the Xparameter button -25- and the value will be changed in steps of 0.1.
Filters high and low frequencies alternately according to the adjusted bar value.
Time parameter value: 100 – 65000 msec
Direct bar assignment: 500/1000/2000/4000/8000/16000 msec
By turning the X parameter knob -25- the value will be changed in steps of 10. Push, hold and turn
the X parameter knob -25- and the value will be changed in steps of 100.
Y parameter dry/wet value: 0 – 100%
Simulates reecting sound waves in a naturally restricted area.
Time parameter value: 0 – 100%
Direct bar assignment: 0/20/40/60/80/100%
By turning the X parameter knob -25 the value will be changed in steps of 1. Push, hold and turn the
X parameter knob -25- and the value will change in steps of 10.
Y parameter dry/wet value: 0 – 100%
Creates the signal‘s chopping by fading in and out, similar to fast cutting with the crossfader.
Time parameter value: 25 – 65000 msec.
Direct bar assignment: 500/1000/2000/4000/8000/16000 msec.
By turning the X parameter knob -25- the value changes in steps of 1. Push, hold and turn the X pa-
rameter knob -25- and the value will change in steps of 100.
Y parameter dry/wet value: 0 - 100%
Raises or lowers the signal‘s tone pitch.
Time parameter value: -100 – 100%
Direct bar assignment: -100/-50/-33/0/50/100%
By turning the X parameter knob -25- the value changes in steps of 1. Push, hold and turn the X pa-
rameter knob -25- and the value will change in steps of 10.
Y parameter dry/wet value: 0 - 100%
To Next Page
Loading...
Need help?
General
