RL78/G13 CHAPTER 29 ELECTRICAL SPECIFICATIONS
R01UH0146EJ0100 Rev.1.00 986
Sep 22, 2011
Caution The pins mounted depend on the product. Refer to 2.1.1 20-pin products to 2.1.14 128-pin products,
and 2.1.15 Pins for each product (pins other than port pins).
(2) X1 oscillation: Ceramic resonator (AMPH = 1, TA = − 40 to +85°C)
Recommended Circuit Constants
Oscillation Voltage
Range
Manufacturer Part Number
SMD/
Lead
Frequency
(MHz)
Frash
operation
mode
Note
C1 (pF) C2 (pF) Rd (kΩ) MIN. (V) MAX. (V)
CSTCE12M0G52-R0 SMD 12.0 Internal (10) Internal (10) 0
CSTCE16M0V53-R0 SMD Internal (15) Internal (15) 0
CSTLS16M0X51-B0 Lead
16.0
Internal (5) Internal (5) 0
CSTCE20M0V51-R0 SMD Internal (5) Internal (5) 0
Murata
Manufacturing
Co., Ltd.
CSTLS20M0X51-B0 Lead
20.0
HS
Internal (5) Internal (5) 0
2.4 5.5
CCR16.0MX7 SMD 16.0 4 4 0
TDK
Corporation
CCR20.0MX7 SMD 20.0
HS
4 4 0
2.4 5.5
Note Set the flash operation mode by using CMODE1 and CMODE0 bits of the option byte (000C2H/010C2H).
Remark Values in parentheses in the C1, C2 columns indicate an internal capacitance.
(3) X1 oscillation: Crystal resonator (AMPH = 0, T
A = − 40 to +85°C)
Recommended Circuit Constants
Oscillation Voltage
Range
Manufacturer Part Number
SMD/
Lead
Frequency
(MHz)
Frash
operation
mode
Note1
C1 (pF) C2 (pF) Rd (kΩ) MIN. (V) MAX. (V)
SMD LS 3 4 0 1.8 5.5
Nihon Dempa
Kogyo
Co., Ltd.
Note2
NX8045GB
SMD
8.0
HS 5 5 0 2.4 5.5
Notes 1. Set the flash operation mode by using CMODE1 and CMODE0 bits of the option byte (000C2H/010C2H).
2. When using this resonator, contact Nihon Dempa Kogyo Co., Ltd (http://www.ndk.com/en).
(4) X1 oscillation: Crystal resonator (AMPH = 1, T
A = − 40 to +85°C)
Recommended Circuit Constants
Oscillation Voltage
Range
Manufacturer Part Number
SMD/
Lead
Frequency
(MHz)
Frash
operation
mode
Note1
C1 (pF) C2 (pF) Rd (kΩ) MIN. (V) MAX. (V)
NX5032GA SMD 16.0 6 7 0
Nihon Dempa
Kogyo
Co., Ltd.
Note2
NX3225HA SMD 20.0
HS
4 5 0
2.4 5.5
Notes 1. Set the flash operation mode by using CMODE1 and CMODE0 bits of the option byte (000C2H/010C2H).
2. When using these resonators, contact Nihon Dempa Kogyo Co., Ltd (http://www.ndk.com/en).
Caution The oscillator constants shown above are reference values based on evaluation in a specific
environment by the resonator manufacturer. If it is necessary to optimize the oscillator characteristics
in the actual application, apply to the resonator manufacturer for evaluation on the implementation
circuit. The oscillation voltage and oscillation frequency only indicate the oscillator characteristic. Use
the RL78/G13 so that the internal operation conditions are within the specifications of the DC and AC
characteristics.