2.Press any key to stop all channel scan, except FUN and Power key.
Note:
· In addition to memory channel with special functions, there must be two or more mobile radio memory channels included data.
Call Scan
You can monitor the call channel and the current operating frequency in turn.
1.Choose the monitored frequency (In VFO or memory call-out mode)
·In VFO mode, rotate the coding knob or press microphone UP/DWN key to choose the needed frequency.
·In memory call-out mode, rotate the coding knob or press microphone UP/DWN key to choose the monitored memory channel.
2.Press CALL key for (1s) to start call scan.
·The mobile radio monitors the call channel and the selected VFO frequency or memory channel.
3.Press any key except FUN and Power key to stop call scan.
Note:
CALL key function must be equipped with CALL (menu number 18) before using call scan. Otherwise, the mobile radio will transmit 1750Hz
tone. Call scan still can be proceeded even the called out memory channel is locked.
Memory Channel Lock
Channel numbers that not want to be monitored can be locked during scanning memory channel or group.
1.Press MR key, then rotate the coding knob or press microphone UP/DWN key to choose the locked memory channel.
2.Press FUN and MHZ/SET key, then rotate the coding knob to choose menu number 13 (L.OUT).
3.Press MHZ/SET key and rotate the coding knob to choose ON or OFF (default).
4.Press MHZ/SET key to save settings, or press any other key to cancel.
5.Press any other key to exit menu mode, except MHZ/SET key.
·When symbol appears under the memory channel number, the channel is locked.
6.To unlock memory channel, repeat the step 1~5 and choose OFF in step 3.
· symbol disappears.
Note:
·Programming scan channel (L0/U0~L1/U1) and the call channels can’t be locked.
·Call scan can be proceeded between the call channel and the memory channel, even the memory channel is locked.
Scan Restoration Method
The mobile radio will stop scanning when detecting the frequency or the memory channel signal. The mobile radio will continue or stop to
scan according to restoration methods you choose.
·Time Operating Mode (Default)
The mobile radio stays for about 5s on the busy frequency ( or memory channel). The mobile radio will continue to scan, even the signal still
exists.
·Carrier Operating Mode
The mobile radio stays on the busy frequency ( or memory channel) until the signal disappears. There has for 2s delay between the signal
disappears and the scan restores.
·Search Mode
The mobile radio moves to the frequency or the memory channel that signal exists, and stops.
Change Scan Restoration Method
1.Press FUN, MHZ/SET key in turn, then rotate the coding knob to choose menu number 12 (SCAN).
2.Press MHZ/SET key and rotate the coding knob to choose TO (time operating: default), CO (carrier operating), or SE (search) mode.
3.Press MHZ/SET key to save new settings, or press any other key to cancel.
4.Press any other key to exist menu mode, except MHZ/SET key.
Note: to pause scan and monitor weak signals, press the microphone PF key with MONI function. Press MONI key again to restore scan.
CTCSS/DCS
CTCSS/DCS Set Receiving and Transmitting CTCSS/DCS
1.Press FUN, MHZ/SET key in turn, then rotate the coding knob or press microphone UP/DWN key to choose menu number 2 (C-CD).
2.Press MHZ/SET key and rotate the coding knob to choose the needed CTCSS/DCS signaling code.
•Press CALL/TONE key to switch signaling code.
3.Press MHZ/SET key to save new settings, or press any other key to cancel.
4.Press any other key to exist menu mode, except MHZ/SET key.
Set Receiving CTCSS/DCS Signaling Code
1.Press FUN, MHZ/SET key in turn, then rotate the coding knob or press microphone UP/DWN key to choose menu number 3 (R-CD).
2.Press MHZ/SET key and rotate the coding knob to choose the needed CTCSS/DCS signaling code.
•Press CALL/TONE key to switch signaling code.
3.Press MHZ/SET key to save new settings, or press any other key to cancel.
4.Press any other key to exist menu mode, except MHZ/SET key.
Set Transmitting Signal Code
1.Press FUN, MHZ/SET key in turn, then rotate the coding knob or press microphone UP/DWN key to choose menu number 4 (T-CD).
2.Press MHZ/SET key and rotate the coding knob to choose the needed CTCSS/DCS signaling code.
•Press CALL/TONE key to switch signaling code.
3.Press MHZ/SET key to save new settings, or press any other key to cancel.
4.Press any other key to exist menu mode, except MHZ/SET key.
Note: when setting CTCSS/DCS signaling code in step 2, press CALL/TONE key to switch signaling code types, as following shown:
OFF CTCSS DCSN DCS I OFF
When setting DCS signaling code, the screen displays DCS; When setting CTCSS signaling code, the screen displays CT.
10
To Next Page
Loading...
