DCS-I
13
14
15
16
17
18
19
20
21
34
35
36
37
38
39
40
41
42
D071N
D072N
D073N
D074N
D114N
D115N
D116N
D122N
D125N
D205N
D212N
D223N
D225N
D226N
D243N
D244N
D245N
D246N
55
56
57
58
59
60
61
62
63
76
77
78
79
80
81
82
83
84
97
98
99
100
101
102
103
104
105
D325N
D331N
D332N
D343N
D346N
D351N
D356N
D364N
D365N
D523N
D526N
D465N
D466N
D503N
D506N
D516N
D523N
D526N
D664N
D703N
D712N
D723N
D731N
D732N
D734N
D743N
D754N
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
D023I
D025I
D026I
D031I
D032I
D036I
D043I
D047I
D051I
D053I
D054I
D065I
D071I
D072I
D073I
D074I
D114I
D115I
D116I
D122I
D125I
D131I
D132I
D134I
D143I
D145I
D152I
D155I
D156I
D162I
D165I
D172I
D174I
D205I
D212I
D223I
D225I
D226I
D243I
D244I
D245I
D246I
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
D251I
D252I
D255I
D261I
D263I
D265I
D266I
D271I
D274I
D306I
D311I
D315I
D325I
D331I
D332I
D343I
D346I
D351I
D356I
D364I
D365I
D445N
D446N
D452N
D454N
D455N
D462N
D464N
D465N
D466N
D503N
D506N
D516N
D462I
D464I
D465I
D466I
D503I
D506I
D516I
D523I
D526I
D532I
D546I
D565I
D606I
D612I
D624I
D627I
D631I
D632I
D645I
D654I
D662I
D664I
D703I
D712I
D723I
D731I
D732I
D734I
D743I
D754I
CTCSS and DCS Signaling Code Scan
1.Press FUN, MHZ/SET key in turn, then rotate the coding knob to choose menu number 3 (R-CD).
2. Press [MHZ/SET] and then [CALL/TONE] to switch the signaling code type. Press [MHZ/SET] to determine the type.
3.Press MHZ/SET key for (1s) to start CTCSS/DCS signaling code scan.
•When scanning, the point after R-CD flashes.
•To reverse scan direction, rotate the coding knob or press microphone UP/DWN key.
•Press any key to exit function.
•When recognizing CTCSS/DCS signaling code, the signaling code appears and flashes.
4.Press MHZ/SET key to program the recognized signaling code to replace current CTCSS/DCS signaling code. Press any other key to exit
CTCSS/DCS signaling code scan.
•Rotate the coding knob or press microphone UP/DWN key to restore scan when the recognized signaling code flashes.
5.Press any other key to exit menu mode, except MHZ/SET key.
Note:
・When proceeding CTCSS/DCS signaling code scan, CTCSS/DCS function is automatically activated, (even current signaling code doesn’t
set CTCSS/DCS).
・ In the process of scanning, the received signal can be monitored with the speaker.
・ If the signal is not detected, CTCSS/DCS signaling code scan doesn’t scan.
Repeater Function and Form
1. Hold down [MHZ/SET] to set the main frequency.
• When the TX-L is displayed, the main frequency information is displayed on the left screen
• When the TX-R is displayed, information about the main frequency is displayed on the right screen
2.Choose receiving frequency
3.Choose frequency difference direction
4.Choose frequency difference
5.Choose CTCSS/DCS signaling code (If needs)
Program Frequency Difference
Firstly, choose downward frequency of amateur radio repeater station. The methods as described in choose frequency difference.
Choose frequency difference direction
Choose transmitting frequency higher or lower receiving frequency.
1.Press FUN, MHZ/SET key in turn, then rotate the coding knob to choose menu number 5 (SFT).
2.Press MHZ/SET key and rotate the coding knob to choose + or -.
3.Press MHZ/SET key to save settings, or press any other key to cancel.
4.Press any other key to exit menu mode, except MHZ/SET key.
12
To Next Page
Loading...
