1.Press FUN, MHZ/SET key in turn, then rotate the coding knob to choose menu number 56 (MSKGP).
2.Press MHZ/SET key and rotate the coding knob to choose wanted call number, OFF (default) or 1~10.
3.Press MHZ/SET key to save settings, or press any other key to cancel.
4.Press any other key to exit menu mode, except MHZ/SET key.
Note: MSK pre-carrier time: interval time is from pressing PTT key to MSK starts to send carrier, and can be set through PC programming
software.
● MSK Decoding
● MSK ID Number Setting
Input the mobile radio MSK ID number through ID setting of the MSK setting in the PC programming software.
● MSK Reset Time
MSK reset time refers to remain time length after MSK encoding is right, such as setting 10M refers to remaining the correct status in 10
minutes after MSK encoding is right. Proper MSK reset time can be selected as needed.
1.Press FUN, MHZ/SET key in turn, then rotate the coding knob to choose menu number 57 (MSKRT).
2.Press MHZ/SET key and rotate the coding knob to choose wanted call number, OFF (default) or 1M~10M (Minute).
3.Press MHZ/SET key to save settings, or press any other key to cancel.
4.Press any other key to exit menu mode, except MHZ/SET key.
Additional Function
Respond Method
1.Press FUN, MHZ/SET key in turn, then rotate the coding knob to choose menu number 14 (ECHO).
2. Press [MHZ/SET], then turn the encoding knob to select "D-RX" or "S-RX".
3.Press MHZ/SET key to save settings, or press any other key to cancel.
4.Press any other key to exit menu mode, except MHZ/SET key.
APO (Auto Power Off)
If don’t press keys or adjust control knobs in the selected time, the mobile radio will auto power off. The mobile radio will make several-sec-
ond warning beep before power off 1 minute and APO symbol flashes. Selective APO time: OFF, 30, 60, 90, 120, or 180 minutes.
1.Press FUN, MHZ/SET key in turn, then rotate the coding knob to choose menu number 17 (APO).
2.Press MHZ/SET key and rotate the coding knob to choose APO time, OFF (default), 30, 60, 90, 120, or 180 minutes.
3.Press MHZ/SET key to save settings, or press any other key to cancel.
4.Press any other key to exit menu mode, except MHZ/SET key.
Note:
• APO still timing even the mobile radio is scanning.
• APO timer starts timing when keys are not pressed, control knob is not adjusted and PC control orders are not detected.
S-meter Squelch
If S-meter squelch function is activated, squelch of the mobile radio will be activated only when received signal intensity higher or equal to
S-meter setting. It avoids constantly resetting squelch when receiving weak stations.
1.Press FUN, MHZ/SET key in turn, then rotate the coding knob to choose menu number 8 (SQL).
2.Press MHZ/SET key and rotate the coding knob to choose S-meter level, OFF (default), S0, S1, S2, S3, S4, S5, S6, S7.
• If S0-S7 any level is selected, squelch knob is no longer working.
3.Press MHZ/SET key to save settings, or press any other key to cancel.
4.Press any other key to exit menu mode, except MHZ/SET key.
Squelch Delay Time
When S-meter squelch function is used, time span from the received signal disappearing to the squelch being turned off needs to be
adjusted.
1.Press FUN, MHZ/SET key in turn, then rotate the coding knob to choose menu number 9 (SQH).
2.Press MHZ/SET key and rotate the coding knob to choose OFF (default), 125, 250 or 500msec.
3.Press MHZ/SET key to save settings, or press any other key to cancel.
4.Press any other key to exit menu mode, except MHZ/SET key.
Beep Function
Beep function checks the input, wrong prompting and fault. Suggest turning on the function to check wrong operations and fault. But if
wants to turn off the function
1.Press FUN, MHZ/SET key in turn, then rotate the coding knob to choose menu number 23 (BP).
2.Press MHZ/SET key and rotate the coding knob to choose OFF.
3.Press MHZ/SET key to save settings, or press any other key to cancel.
4.Press any other key to exit menu mode, except MHZ/SET key.
The mobile radio will make following warning beep sound even the beep function is turned off.
• APO warning beep
• TOT warning beep
Busy Channel Lockout
With this function, it can avoid transmitting on the used channel or frequency by others. When the function is turned on, if the channel or
frequency is used by others, press PTT key and the mobile radio will make a wrong beep sound and doesn’t transmit.
1.Press FUN, MHZ/SET key in turn, then rotate the coding knob to choose menu number 21 (BCL).
2.Press MHZ/SET key and rotate the coding knob to choose ON or OFF (default).
3.Press MHZ/SET key to save settings, or press any other key to cancel.
4.Press any other key to exit menu mode, except MHZ/SET key.
Frequency Step Size
When using coding knob or microphone UP/DWN key to choose receiving frequency, frequency step size must be chosen correctly.
Change Frequency Step Size
1.In VFO mode, press FUN, MHZ/SET key in turn, then rotate the coding knob to choose menu number 1 (STP).
16
To Next Page
Loading...
