To Next PageTo Next Page
Need help?Do you have a question about the Rheem RGFG and is the answer not in the manual?
Specific safety compliance mandates for MA.
Requirements for CO detector installation and types.
Manufacturer guidelines for venting system components.
Items to verify for proper gas supply installation.
Items to verify for proper electrical installation.
Items to verify for correct furnace installation.
Items to verify for duct static pressure.
Items to verify for condensate line setup.
Items to verify for direct vent pipe installation.
Items to verify for non-direct vent pipe installation.
Key considerations for furnace placement and environmental factors.
Specific guidelines for upflow furnace duct installations.
Overview of venting requirements and safety precautions.
Explanation of safety switches and their function.
Procedures for integrating with existing vent systems.
Guidelines for safely joining PVC vent pipes and fittings.
Guidelines for providing adequate combustion air.
Requirements for furnaces installed in unconfined spaces.
Procedures for supplying combustion air from indoor spaces.
Procedures for supplying combustion air from outdoor spaces.
Specific rules for non-direct vent piping installations.
Rules for direct vent piping installation and termination.
Specific instructions for standard vertical vent terminations.
Details on the concentric vent kit and its components.
Diagram and notes for vertical concentric vent installation.
Diagram and notes for horizontal concentric vent installation.
Diagram for vertical installation of side wall vents.
Diagram for horizontal installation of side wall vents.
Specific instructions for standard horizontal vent terminations.
Details on installing combustion air piping for alternate terminations.
Details on installing exhaust vent piping for alternate terminations.
Specifics on terminating exhaust vents for alternate horizontal setups.
Rules for individually venting multiple furnaces.
Specific connection details for upflow models.
Important notes and warnings regarding condensate drainage.
Specific installation steps for upflow models' condensate drain.
Steps for moving the trap on upflow models.
Information on natural gas use and LP conversion.
Procedures for installing gas piping according to codes.
Important notes and warnings related to LP conversion.
Steps to measure and set the supply gas pressure.
Procedures for measuring and adjusting manifold gas pressure.
Critical safety information regarding electrical connections and grounding.
Steps to check incoming power and wiring polarity.
Procedure to verify the 24 VAC control voltage.
Details on optional accessories requiring field installation.
Information on installing and operating an electronic air cleaner.
Information on installing and controlling humidifiers and dehumidifiers.
Setup for humidification control without dehumidification.
Setup for dehumidification control without humidification.
Specific setup for non-communicating thermostats.
Control options requiring optional humidifiers.
Setup for communicating thermostats.
Setup for non-communicating thermostats with optional humidistat.
Specific conversion procedures for RGFG models at altitude.
Examples illustrating orifice selection for altitude adjustments.
Canadian derating methods for LP gas furnaces at altitude.
Configuration for achieving high SEER cooling operation.
Explanation of the furnace control's status and diagnostic display.
How to set and operate the fan in continuous mode.
Specific wiring and setup for mixed communicating systems.
Connections for 24VAC thermostats.
Control connections for the gas valve and motors.
Details on network connections and status LEDs.
Location and purpose of the memory card connector.
Guidelines for using and transferring furnace shared data.
Steps taken when no memory card is detected.
Steps taken when a memory card is present.
Critical steps for managing the memory card when replacing the control.
Specific settings for S3 dipswitches affecting cooling and heat-pump airflow.
Settings for S4 dipswitches related to test modes and airflow selection.
Furnace operation with modulating thermostats.
Furnace operation with two-stage thermostats.
Furnace operation with single-stage thermostats.
How to interpret the furnace's diagnostic display.
How fault codes are stored and managed.
Guidelines for wiring thermostats in communicating systems.
Important notes regarding communicating system wiring.
Information displayed in the Status 1 menu.
Details on the status of key limit controls.
Procedures for resetting defaults and viewing dipswitch settings.
Adjusting cooling, heating, and fan airflow rates.
Settings for dehumidification, staging, and dual-fuel modes.
Adjusting settings for dual-fuel system operation.
Specific steps for igniting the furnace burners.
Steps involved in starting the heating cycle.
How the furnace responds to heating demands.
Process of ending the heating cycle.
Instructions for cleaning, replacing, and resizing furnace filters.
Troubleshooting steps for missing or invalid shared data.
Troubleshooting for corrupt or invalid memory card data.
Troubleshooting for mismatched hardware and data.
Troubleshooting for mismatched blower motor horsepower.
Troubleshooting for unsupported blower motor manufacturers.
Troubleshooting for shared data from older furnace models.
Fault code related to gas heat operation without V signal.
Troubleshooting for repeated ignition failures.
Troubleshooting steps for igniter failures.
Troubleshooting for issues related to flame sense rod.
Troubleshooting steps when flame is lost during operation.
Troubleshooting for igniter circuit failures.
Troubleshooting for flame detected when gas valve is off.
Troubleshooting for main limit switch opening.
Troubleshooting for heat-assisted limit control opening.
Troubleshooting for reversed line and neutral wiring.
Troubleshooting for manual reset limit control opening.
Troubleshooting for LPC switch closing when it should be open.
Troubleshooting for LPC switch opening during operation.
Troubleshooting for LPC switch opening during operation (continuation).
Troubleshooting for HPC switch opening.
Troubleshooting for HPC switch opening (continuation).
Troubleshooting for blower faults during operation.
Troubleshooting for blower faults when it fails to run.
Troubleshooting for blower operating at excessive speed.
Troubleshooting for loss of communication with the blower motor.
Troubleshooting for loss of communication with the inducer motor.
Troubleshooting for issues with gas valve feedback.
Troubleshooting for general furnace control faults.
Wiring instructions for non-communicating thermostats.
Furnace operation modes with various thermostat types.
Details on furnace operation with modulating thermostats.
Steps for removing the existing thermostat.
Step-by-step guide for installing a new thermostat.
Explanation of elements on the thermostat's main screen.
Guide to programming and configuring thermostat settings.
Description of the main configuration menu items.
Options for adjusting backlight intensity and display.
Settings for programming schedules and energy saving features.
Settings for temperature limits and keypad lockout.
Settings for staging, sensors, dual-fuel, and filter reminders.
How to select fan and system modes.
Guide to programming schedules and temporary overrides.
Using automatic schedules and fan programming.
Steps for setting programs and using copy functions.
Information on factory settings and planning custom programs.
Installation and configuration of remote temperature sensors.
Setting the dual fuel changeover temperature.
Steps for resetting the thermostat to factory defaults.
Troubleshooting common operational issues with potential causes and fixes.
Instructions for wiring thermostats in communicating systems.
Important notes regarding communicating system wiring.
Procedure for initial startup of communicating systems.
Guidance on navigating thermostat menus.
Steps to view fault messages on the thermostat.
How to access the fault status screen on the thermostat.
Step-by-step instructions for navigating thermostat menus.
Steps for accessing and changing settings within the thermostat's setup menus.
Steps to select and change setup values.
Process of updating system settings after changes.
Confirmation screen indicating a successful setting update.
How to exit the setup menus and return to the main screen.
General
