Rigol DS6064

To Next Page

To Previous Page

1 Quick Start RIGOL

DS6000 User’s Guide 1-5

To Adjust the Supporting Legs

Adjust the supporting legs properly to use them as stands to tilt the oscilloscope

upwards for stable placement of the oscilloscope as well as better operation and

observation of the display. Unfold or fold the supporting legs in the arrow directions

as shown in the figures below.

Figure 1-4 To Adjust the Supporting Legs

Supporting Legs

Main Page

Guaranty and Declaration3
Safety Requirement4
- General Safety Summary4
- Safety Notices and Symbols7
- Allgemeine Sicherheits Informationen8
- Sicherheits Begriffe und Symbole11
- Measurement Category12
- Ventilation Requirement13
- Working Environment14
  - Pollution Degree15
  - Pollution Degree Definitions15
- Care and Cleaning16
- Environmental Considerations17
DS6000 Series Overview19
Document Overview21
- Table of Contents24
1 Quick Start31
- General Inspection32
- Appearance and Dimensions33
- Preparations for Use34
- Front Panel Overview45
- Rear Panel Overview47
- Front Panel Function Overview49
- User Interface57
- Trigger Type59
- Security Lock63
- Desk Mount Instrument Arm64
- Built-In Help System65
2 To Set the Vertical System67
- To Enable the Channel68
- Channel Coupling69
- Bandwidth Limit70
- Probe71
- Input Impedance75
- Waveform Invert75
- Vertical Scale76
- Vertical Position77
- Vertical Expansion78
- Amplitude Unit78
- Channel Label79
- Delay Calibration80
3 To Set the Horizontal System81
- Delayed Sweep82
- Time Base Mode84
- Horizontal Scale89
- Horizontal Position89
- Horizontal Reference91
4 To Set the Sample System93
- Acquisition Mode94
- Sample Mode97
  - Real-Time Sample97
  - Equivalent Sample97
- Sample Rate98
- Memory Depth100
- Anti-Aliasing101
5 To Trigger the Oscilloscope103
- Trigger Source104
- Trigger Mode105
- Trigger Coupling107
- Trigger Holdoff108
- Trigger Type109
- Trigger Output Connector135
6 To Make Measurements137
- Math Operation138
- Auto Measurement150
- Cursor Measurement165
7 Protocol Decoding179
- Parallel Decoding180
- RS232 Decoding (Option)183
- I2C Decoding (Option)188
- SPI Decoding (Option)191
- CAN Decoding (Option)195
- Flexray Decoding (Option)199
8 Reference Waveform203
- To Enable REF Function204
- To Set the Color205
- To Select REF Source206
- To Save to Internal Memory206
- To Adjust REF Waveform Display206
- To Export to Internal or External Memory207
- To Import from Internal or External Memory207
9 Pass/Fail Test209
- To Enable Pass/Fail Test Function210
- To Select Source211
- Mask Range211
- Test and Output212
- To Save the Test Mask213
- To Load the Test Mask213
10 Waveform Recording215
- Record Constant on218
- Waveform Playback219
- Waveform Analysis221
  - Analysis Based on Trace224
  - Analysis Based on Pass/Fail Mask225
11 Display Control227
- To Select the Display Type228
- To Set the Persistence Time229
- To Set the Waveform Brightness231
- To Set the Screen Grid231
- To Set the Grid Brightness231
- To Set the Menu Display231
12 Store and Recall233
- Storage System234
- Storage Type235
- Internal Store and Recall237
- External Store and Recall240
- Disk Management242
- Factory249
13 System Function Setting257
- Remote Interface Configuration258
- System-Related263
- To Print the Waveform271
14 Remote Control275
- Remote Control Via USB276
- Remote Control Via LAN280
- Remote Control Via GPIB282
15 Troubleshooting285
16 Specifications287
- General Specifications294
- Calibration Interval294
17 Appendix295
- Appendix A: Accessories and Options295
- Appendix B: Warranty296
Index297

Table of Contents

Other manuals for Rigol DS6064

Related product manuals