RKC INSTRUMENT CB100 Series - Page 247

Temperature Controller Driver
GP-Pro EX Device/PLC Connection Manual
247
67 AW Input error determination point (low) [H-TIO-, H-CIO-A, H-SIO-A]
68 WH Action at input error (high) [H-TIO-
, H-CIO-A, H-SIO-A]
69 WL Action at input error (low) [H-TIO-
, H-CIO-A, H-SIO-A]
6A GB AT bias [H-TIO-
, H-CIO-A, H-SIO-A]
6B OH
Output limiter (high) [For heat/cool control:Heat-side output limiter (high)] [H-TIO-
,
H-CIO-A, H-SIO-A]
6C OL
Output limiter (low) [For heat/cool control:Cool-side output limiter (high)] [H-TIO-
, H-
CIO-A, H-SIO-A]
6D IV ON/OFF control differential gap (upper) [H-TIO-
, H-CIO-A, H-SIO-A]
6E IW ON/OFF control differential gap (lower) [H-TIO-
, H-CIO-A, H-SIO-A]
6F OE Manipulated output value at input error [H-TIO-
, H-CIO-A, H-SIO-A]
70 PH Output change rate limiter (up) [H-TIO-
, H-CIO-A, H-SIO-A]
71 PL Output change rate limiter (down) [H-TIO-
, H-CIO-A, H-SIO-A]
72 XE Direct/Reverse action selection [H-TIO-
, H-CIO-A, H-SIO-A]
73 XN Hot/Cold start selection [H-TIO-
, H-CIO-A, H-SIO-A]
74 SX Start determination point [H-TIO-
, H-CIO-A]
75 X1 Control RUN/STOP holding [H-PCP-J]
76 EK Temperature rise completion hold function [H-PCP-J]
77 ZX Interval time setting COM.PORT1/COM.PORT2 [H-PCP-J]
78 ZY Interval time setting COM.PORT3 [H-PCP-J]
79 HA Alarm 1 differential gap [H-TIO-
, H-CIO-A, H-SIO-A]
7A HB Alarm 2 differential gap [H-TIO-
, H-CIO-A, H-SIO-A]
7B XA Alarm 1 type selection [H-TIO-
, H-CIO-A, H-SIO-A]
7C XB Alarm 2 type selection [H-TIO-
, H-CIO-A, H-SIO-A]
7D WA Alarm 1 hold action [H-TIO-
, H-CIO-A, H-SIO-A]
7E WB Alarm 2 hold action [H-TIO-
, H-CIO-A, H-SIO-A]
7F LA Alarm 1 interlock [H-TIO-
, H-CIO-A, H-SIO-A]
80 LB Alarm 2 interlock [H-TIO-
, H-CIO-A, H-SIO-A]
81 OA Alarm 1 action at input error [H-TIO-
, H-CIO-A, H-SIO-A]
82 OB Alarm 2 action at input error [H-TIO-
, H-CIO-A, H-SIO-A]
83 DF Number of alarm delay times [H-TIO-
, H-CIO-A, H-SIO-A]
84 CL Module initialization [H-PCP-J]
85 ZF CT channel setting [H-CT-A]
86 LT DO function selection [H-DO-A/B/D]
87 XK DI function selection [H-DI-A]
88 H2 DI using selection [H-DI-A]
89 VK AI input range number [H-AI-A/B]
8A JS AI display scale high [H-AI-A/B]
8B JV AI display scale low [H-AI-A/B]
8C HC AI alarm 1 differential gap [H-AI-A/B]
8D HF AI alarm 2 differential gap [H-AI-A/B]
8E XC AI alarm 1 type selection [H-AI-A/B]
8F XD AI alarm 2 type selection [H-AI-A/B]
90 WC AI alarm 1 hold action [H-AI-A/B]
91 WD AI alarm 2 hold action [H-AI-A/B]
92 LC AI alarm 1 interlock [H-AI-A/B]
93 LD AI alarm 2 interlock [H-AI-A/B]
94 TK Number of AI alarm delay times [H-AI-A/B]
95 JU AI decimal point position [H-AI-A/B]
96 JT Power supply frequency selection [H-PCP-J]
97 F2 AI digital filter [H-AI-A/B]
98 VA AI moving average [H-AI-A/B]
99 XV Display scale high [H-TIO-H/J,H-CIO-A,H-SIO-A]
Address Identifier Description