RKC INSTRUMENT CB100 Series - Page 246

Temperature Controller Driver
GP-Pro EX Device/PLC Connection Manual
246
33 XO AO function selection [H-AO-A/B]
34 OY AO corresponding channel setting [H-AO-A/B]
35 CV AO zooming high limit [H-AO-A/B]
36 CW AO zooming low limit [H-AO-A/B]
37 JK AO zero point correction [H-AO-A/B]
38 JL AO full scale correction [H-AO-A/B]
39 L1 H-DI-A module input status [H-DI-A]
3A C2 CC-Link selecting flag
3B Q3 Event DO status [H-DO-C]
3C Q4 Event DO manual output value [H-DO-C]
3D A7 Event DO extension alarm set value [H-DO-C]
3E KH Cascade monitor [H-CIO-A]
3F KF Cascade ON/OFF [H-CIO-A]
40 KG Cascade gain [H-CIO-A]
41 KI Cascade bias [H-CIO-A]
42 M7 TI measured value [H-TI-A/B/C]
43 AF TI alarm 1 status [H-TI-A/B/C]
44 AG TI alarm 2 status [H-TI-A/B/C]
45 B2 TI burnout status [H-TI-A/B/C]
46 A8 TI alarm 1 set value [H-TI-A/B/C]
47 A9 TI alarm 2 set value [H-TI-A/B/C]
48 PC TI PV bias [H-TI-A/B/C]
49 EJ TI operation mode transfer [H-TI-A/B/C]
4A L3 PCP module DI status
4B L4 Event DI contact input monitor [H-DI-B]
4C L5 Event DI logic input monitor [H-DI-B]
4D Q5 Event DI logic output monitor [H-DI-B]
4E AH H-CT-A module heater break alarm status [H-CT-A]
4F AJ Comprehensive alarm status [H-PCP-J]
50 M8 Positioning monitor [H-TIO-K]
51 V3 Positioning output neutral zone [H-TIO-K]
52 TJ Motor time [H-TIO-K]
53 OS Integrated output limiter [H-TIO-K]
54 OO Manual positioning output value [H-TIO-K]
55 C1 Local/Computer transfer
56 HH Setting change rate limiter [H-TIO-
, H-CIO-A, H-SIO-A]
57 D0 H-DO-G manipulated output value [H-DO-G]
58 D2 H-DO-G DO output status [H-DO-G]
59 D3 H-DO-G output limiter (high) [H-DO-G]
5A D4 H-DO-G output limiter (low) [H-DO-G]
5B D5 H-DO-G output cycle time [H-DO-G]
5C D6 H-DO-G Auto/Manual transfer [H-DO-G]
5D D7 H-DO-G manual output value [H-DO-G]
5E D8 H-DO-G master channel setting [H-DO-G]
5F D9 H-DO-G output ratio set value [H-DO-G]
60 ST PLC scanning time setting [H-PCP-J]
61 GY Integral time limiter at AT end [H-TIO-
, H-CIO-A, H-SIO-A]
62 XI Input range number [H-TIO-
, H-CIO-A, H-SIO-A]
63 SH Setting limiter (high) [H-TIO-
, H-CIO-A, H-SIO-A]
64 SL Setting limiter (low) [H-TIO-
, H-CIO-A, H-SIO-A]
65 F1 Digital filter [H-TIO-
, H-CIO-A, H-SIO-A]
66 AV Input error determination point (high) [H-TIO-
, H-CIO-A, H-SIO-A]
Address Identifier Description