Ross Carbonite Series - Keying; To Apply a Border to a DVE Key; Show Alpha

Tip: Hold the SELF KEY, AUTO SELECT, or CHR KEY
button again and press DVE to turn off the Fly Key.
2.
Press the KEY X SEL button for the key you are
setting up. Click DVE and click On.
3.
Use the X Pos, Y Pos, and Size knobs to position
and size the key. You can also use the positioner.
Use the X-Position, Y-Position, and Size sliders
in the Positioning area to position and size the key.
4.
Press NEXT.
5.
Use the Aspect knob to adjust the aspect ratio of
the key. Use the Aspect slider to adjust the aspect
ration of the key.
6.
Use the Border knob to apply a border to the key.
Use the Size and Softness sliders in the Border
area to apply a border to the key.
Refer to the section To Apply a Border to a DVE
Key on page 43 for information on borders.
7.
Press NEXT. If a border is applied to the pattern,
you must press NEXT multiple times to get to the
next step.
8.
Crop the key horizontally as follows:
a)
Use the HCrop knob to crop the key
horizontally on both the left and right sides at
the same time.
b)
Press HCrop and use the Left/R knob to crop
the key horizontally on the left side only.
c)
Press Left/R and use the L/Rgt knob to crop
the key horizontally on the right side only.
9.
Use the Left and Right sliders to crop the left and
right sides of the key.
10.
Crop the key vertically as follows:
a)
Use the VCrop knob to crop the key vertically
on both the top and bottom sides at the same
time.
b)
Press VCrop and use the Top/B knob to crop
the key vertically on the top side only.
c)
Press Top/B and use the T/Bttm knob to crop
the key vertically on the bottom side only.
11.
Use the Left and Right sliders to crop the left and
right sides of the key.
12.
Crop the key vertically as follows:
a)
Use the VCrop knob to crop the key vertically
on both the top and bottom sides at the same
time.
b)
Press VCrop and use the Top/B knob to crop
the key vertically on the top side only.
c)
Press Top/B and use the T/Bttm knob to crop
the key vertically on the bottom side only.
13.
Use the Top and Bottom sliders to crop the upper
and lower sides of the key.
14.
Use the Mask knob to apply a mask to the key.
Click Mask to apply a mask to the key.
To Apply a Border to a DVE Key
1.
Select the keyer that you want to set up a DVE key
border on. Click Navigation Menu > Live Assist
> ME and select the ME and key that you want to
set up.
Tip: You can use the same procedure for a MiniME
™
or
MultiScreen.
2.
Select the video signal, on the key bus, that you want
to use for the key. Click Key Fill and select the
video signal you want to use for the key.
3.
Press DVE. Click DVE.
4.
Use the Border knob to turn on the border and
adjust the size of the border around the key. Use the
Size slider in the Border area to turn on the border
and adjust the size of the border around the key.
5.
Use the Soft knob to adjust the softness of the
border. Use the Softness slider to adjust the
softness of the border.
6.
Press NEXT.
7.
Select a default or custom color for the border.
•
Default — use the Load knob to select a preset
color for the border. Default — click one of the
preset colors.
•
Custom — press NEXT and use the BHue,
BSat, and BLum knobs to select your own
color. Custom — click the arrow to the right of
the Border Color area and use the Hue,
Saturation, and Lightness sliders to select
your own color. Click OK to apply the color or
Live to apply it in real-time.
Show Alpha
The SHOW ALPHA button allows you to route the
processed alpha for the selected keyer to the preview
output for the ME you are working on, as well as the last
available aux bus.
Show alpha is not available on a MiniME
™
or
MultiScreen.
• Select the keyer that you want to show the alpha for
and press and hold the SHOW ALPHA button. The
Carbonite Operation Manual (v13.0) — Keying • 43