Name: rotork CMA Series
Brand: rotork
Rating: 5 (1 reviews)

To Next Page

POSIT

Position

SET PT

Setpoint

THRUST or TORQUE

Thrust Display or

Ouput Torque

LOCAL/REM

Local / Remote Operation

MANJOG

Manual Jog

TORQ/THRUST C

Close Torque/Thrust

TORQ/THRUST O

Open Torque/Thrust

CL ACT

Close Action

OP ACT

Open Action

BASIC

CL LIM

Close Limit (zero)

OP LIM

Open Limit (span)

CMD4

Field Command Signal4

CMD20

Field Command Signal20

DBAND

Deadband

FLTHST

Fault History Access

ADVANC

Advanced Menu

DEFLTS

Default Menu Access

STATUS

Position Display

START POINT

POS

REMOTE

STEP 1

SELECT LOCAL

OPERATION

STEP 1

SET OUTPUT

TORQUE/TRUST

STEP 3

SET CLOSE LIMIT

OF TRAVEL

STEP 4

SET OPEN LIMIT

OF TRAVEL

STEP 5

CALIBRATE COMMAND

SIGNAL ZERO SETPOINT

STEP 6

CALIBRATE COMMAND

SIGNAL SPAN SETPOINT

STEP 2

SELECT ACTION AT END

OF TRAVEL ( LIMIT OR FORCE)

STEP 7

DEADBAND

LOCAL

TC 100

EDIT

LOCAL

TC 600

EDIT

Select desired Torque/Thrust Close

LOCAL

THRSTC

LOCAL

TO 100

EDIT

LOCAL

TO 600

EDIT

LOCAL

THRSTO

Select desired Torque/Thrust Open

Example set at 60%

STEP 1

SELECT LOCAL

OPERATION

STEP 1

SET OUTPUT

TORQUE/TRUST

STEP 3

SET CLOSE LIMIT

OF TRAVEL

STEP 4

SET OPEN LIMIT

OF TRAVEL

STEP 5

CALIBRATE COMMAND

SIGNAL ZERO SETPOINT

STEP 6

CALIBRATE COMMAND

SIGNAL SPAN SETPOINT

STEP 2

SELECT ACTION AT END

OF TRAVEL ( LIMIT OR FORCE)

STEP 7

DEADBAND

LOCAL

CA LIM

EDIT

LOCAL

CA LIM

EDIT

Select Force FRC or Limit LIM

LOCAL

CL ACT

LOCAL

OA LIM

EDIT

LOCAL

OA FRC

EDIT

LOCAL

OP ACT

Select Force FRC or Limit LIM

CMA Range

Quick Start Guide

CML-1500 and CML-3000

LOCAL

CL LIM

EDIT

LOCAL

CL LIM

EDIT

LOCAL

CL LIM

STEP 1

SELECT LOCAL

OPERATION

STEP 1

SET OUTPUT

TORQUE/TRUST

STEP 3

SET CLOSE LIMIT

OF TRAVEL

STEP 4

SET OPEN LIMIT

OF TRAVEL

STEP 5

CALIBRATE COMMAND

SIGNAL ZERO SETPOINT

STEP 6

CALIBRATE COMMAND

SIGNAL SPAN SETPOINT

STEP 2

SELECT ACTION AT END

OF TRAVEL ( LIMIT OR FORCE)

STEP 7

DEADBAND

SAVE

Until

LOCAL

THRSTC

THRSTC or TORQ C

LOCAL

THRSTO

LOCAL

CL ACT

LOCAL

OP ACT

THRSTO or TORQ O

OPEN

LOCAL

CL LIM

www.rotork.com

As part of a process of on-going product development, Rotork reserves the right to amend and change specifications without

prior notice. Published data may be subject to change. For the very latest version release, visit our website at www.rotork.com

The name Rotork is a registered trademark. Rotork recognises all registered trademarks.

Published and produced in the UK by Rotork. POWTG0818

Rotork plc

Brassmill Lane, Bath, UK

tel +44 (0)1225 733200

fax +44 (0)1225 333467

email mail@rotork.com

USA

Rotork Controls

tel +1 (414) 461 9200

fax +1 (414) 461 1024

email info@rotork.com

A full listing of our worldwide

sales and service network is

available on our website.

LOCAL

POS

Move Actuator to CLOSE Position

PUB094-022-00 Issue 08/18

These instructions enable the actuator to be

conﬁgured to suit the valve and must be carried

out before electrical start up. For complete

instructions refer to PUB094-019.

CAUTION: Before commissioning

actuators ﬁtted with the Reserve

Power Pack (RPP), please ensure

PUB094-019 is fully understood and

additional safety instructions are

followed where applicable.

Ensure the local control selector is set to

LOCAL during the commissioning process.

Brand	rotork
Model	CMA Series
Category	Controller
Language	English

rotork CMA Series User Manual

Other manuals for rotork CMA Series

Questions and Answers:

rotork CMA Series Specifications

Related product manuals