To Next PageTo Next PageHow to fix a Samsung Vacuum Cleaner that is not working?
If your Samsung Vacuum Cleaner isn't working, check if the emergency switch is on and if all the icons are displayed on the panel. Also, check if the battery is depleted. If "Lo" is displayed, carry the POWERbot to the charger to charge it. If the remote controller isn't working, replace the batteries (AAA type).
What to do if my Samsung Vacuum Cleaner POWERbot stops during cleaning?
If your Samsung Vacuum Cleaner POWERbot stops during cleaning, ensure that the display panel doesn't show "Lo", indicating low battery. If it does, take the POWERbot to the charger. Also, check for any obstacles like cords or thresholds and remove them. If fabrics or strings are caught in the drive wheel, turn off the emergency switch and remove them before restarting.
How to fix a Samsung POWERbot SR20H9050U POWERbot that is not working?
If your Samsung Vacuum Cleaner POWERbot is not working, first check if the emergency switch is on. Then, verify that all icons are displayed on the display panel. If "Lo" is displayed, the battery is depleted; charge the POWERbot. Lastly, if the remote controller isn't working, replace its batteries (AAA type).
Why can't my Samsung POWERbot SR20H9050U find the charger?
Your Samsung Vacuum Cleaner might be unable to locate the charger due to a power failure, an unplugged power plug, or obstacles around the charger. Check if there is a power failure or if the power plug is unplugged. Remove any obstacles that may be preventing the POWERbot from returning to the charger. Also, clean any foreign matter from the charge pins.
What to do if the filter inspection indicator is still on after emptying the dustbin on my Samsung POWERbot SR20H9050U?
If the filter inspection indicator remains on after emptying the dustbin of your Samsung Vacuum Cleaner, try turning off the emergency switch and then turning it back on. If that doesn't work, empty the dustbin again and thoroughly re-clean the filter.
Why is point cleaning not working on my Samsung Vacuum Cleaner?
Point cleaning might not work if you're directly pointing the red light on the POWERbot. Point the red light on the floor within 50 cm around the POWERbot. Also, avoid using point cleaning under direct sunlight, bright light, or on dark floors.
Why is the battery life so short on my Samsung Vacuum Cleaner Virtual guard?
The battery life of your Samsung Vacuum Cleaner's Virtual guard might be short if you're using manganese drycell batteries. Replace them with new batteries (2 type D (LR20) batteries).
Why is the suction power weak on my Samsung POWERbot SR20H9050U POWERbot?
If your Samsung Vacuum Cleaner POWERbot's suction is weak, and the "Filter inspection indicator" is on, turn off the emergency switch and clean the dustbin. If the dustbin is too full, empty it. Also, check the intake on the bottom of the POWERbot for blockages and remove any foreign matter. If the noise suddenly increases, turn off the emergency switch and empty the dustbin.
What to do if my Samsung POWERbot SR20H9050U Vacuum Cleaner POWERbot cannot find the charger?
If your Samsung Vacuum Cleaner POWERbot can't find the charger, check for a power failure or if the power plug is unplugged. Remove any obstacles around the charger that might be preventing the POWERbot from returning. Clean any foreign matter from the charge pins that could be affecting charging.
What to do if the filter inspection indicator is still on after emptying the dustbin on my Samsung POWERbot SR20H9050U Vacuum Cleaner POWERbot?
If the "Filter inspection indicator" is on your Samsung Vacuum Cleaner POWERbot even after emptying the dustbin, try turning off the emergency switch and then turning it back on. If that doesn't work, empty the dustbin again and thoroughly re-clean the filter.
General| Brand | Samsung |
|---|---|
| Model | POWERbot SR20H9050U Series |
| Category | Vacuum Cleaner |
| Language | English |
Essential safety advice and warnings for operating the appliance.
Broad safety guidelines, including those specific to the charger.
Safety guidelines for operating the robot, including prohibited actions.
How to turn the robot on/off and use the auto clean mode.
Remote functions for power, recharging, and choosing cleaning modes.
Steering the robot and using the point cleaning feature.
How error codes appear and the steps to resolve them.
Solutions for robot not working, stopping, or navigation issues.
Troubleshooting weak suction, charging, and battery life problems.
