- 130 -
Electrical Adjustments
S 664 – Auto Calibration (YCbCr)
– 0 Y - OFFSET AREA H START Y-Offset Area H Start (Unused) 0 ~ 1000 900 –
– 1 Y - OFFSET AREA V START Y-Offset Area V Start (Unused) 0 ~ 1000 500 –
– 2 CB - OFFSET AREA H START CB-Offset Area H Start (Unused) 0 ~ 1000 900 –
– 3 CB - OFFSET AREA V START CB-Offset Area V Start (Unused) 0 ~ 1000 500 –
– 4 CR - OFFSET AREA H START CR-Offset Area H Start (Unused) 0 ~ 1000 900 –
– 5 CB - OFFSET AREA V START CB-Offset Area V Start (Unused) 0 ~ 1000 500 –
– 6 Y - GAIN AREA H START Y-Gain Area H Start 0 ~ 1000 40 –
– 7 Y - GAIN AREA V START Y-Gain Area V Start 0 ~ 1000 495 –
– 8 CB - GAIN AREA H START CB-Gain Area H Start 0 ~ 1000 820 –
– 9 CB - GAIN AREA V START CB-Gain Area V Start 0 ~ 1000 495 –
– 10 CR - GAIN AREA H START CR-Gain Area H Start 0 ~ 1000 690 –
– 11 CR - GAIN AREA V START CB-Gain Area V Start 0 ~ 1000 495 –
– 12 Image AREA H WIDTH YCBCR Level Area H 0 ~ 4095 9 –
– 13 Image AREA V HIGHT YCBCR Level Area V 0 ~ 4095 13 –
– 14 Y - OFFSET TARGET Y-Offset target (Unused) 0 ~ 1023 0 –
– 15 CB - OFFSET TARGET CB-Offset target (Unused) 0 ~ 1023 512 –
– 16 CR - OFFSET TARGET CR-Offset target (Unused) 0 ~ 1023 512 –
– 17 Y - GAIN TARGET Y-Gaint target 0 ~ 1023 870 –
– 18 CB - GAIN TARGET CB-Gaint target 0 ~ 1023 947 –
– 19 CR - GAIN TARGET CR-Gaint target 0 ~ 1023 947 –
– 20 OFFSET tolerance Offset tolerance 0 ~ 1023 1 –
– 21 GAIN tolerance Offset tolerance 0 ~ 1023 1 –
S 680 – Auto PC Adjust
– 0 Auto PC Adjust Enable 0 : Enable / 1 : Disable 0 ~ 1 0 –
– 1 Frequency Step 0 ~ 3 1 –
– 2 Frequency Threshold 0 ~ 10 5 –
– 3 Fine Phase 0 : Execute / 1 : Unexecute 0 ~ 1 0 –
– 4 BLKDET BlacK Level Detect Area 0 ~ 3 1 –
– 5 PHASEMSK 0 : Full bit Enable / 1: 1 last bit disable/ 0 ~ 3 0 –
2 : 2 last bit disable / 3 : 3 last bit Enable
S 700 – General
– 0 IP Mode Setting IP OFF ( 0 : IP Block Unused / 1 : IP Block used and IP OFF) 0 ~ 1 1 –
– 1 3:2 Pull Down Mode Bit0 : Gloobal Mode / Bit1 : Video Mode 1 ~ 3 1 –
– 2 Detect Film Mode Enable
0 : 2:3 pull down & 2:2 pull down / 1 : 2:3 pull down / 2 : 2:2 pull down
0 ~ 2 0 –
– 3 Force IP Mode
0 : IP Process Disable / 1 : Force Normal IP Mode / 2 : Force Film Mode
0 ~ 2 2 –
S 701 – Deinterlacer setting Only Enable Progressive ON / Film
– 0 Motion Adaptive Weight Value < KDEINT > 0 ~ 255 25 –
– 1 Angle Interpolation Level 0 : Conservation < ==== > 4 : Aggressive 0 ~ 4 2 –
– 2 Cue Low Pass Filter Enable < CUELPFEN > 0 ~ 1 0 –
– 3 Motion Override Enable < MTNOVREN > 0 ~ 1 0 –
– 4 Motion Override Value < MTNOVRVAL > 0 ~ 15 0 –
S 710 – Noise Reduction Enable N.R L1
– 0 Noise Level < NOISELEVEL > 0 ~ 1023 10 –
S 711 – Noise Reduction Only Enable N.R L1
– 0 Noise Pixel Range < NSRANGEY > / <NSRANGEUV> 0 ~ 2 1 –
– 1 Noise Region 0 < NSRGIONY0 > / <NSRGIONUV0> 0 ~ 1023 12 –
– 2 Noise Region 1 < NSRGIONY1 > / <NSRGIONUV1> 0 ~ 1023 24 –
– 3 Noise Region 2 < NSRGIONY2 > / <NSRGIONUV2> 0 ~ 1023 40 –
– 4 Noise Gain Level < NSFILTERY** > / <NSFILTERUV**> 0 ~ 255 50 –
S 712 – Noise Reduction Enable N.R L2
– 0 Noise Level < NOISELEVEL > 0 ~ 1023 10 –
S 713 – Noise Reduction Only Enable N.R L2
– 0 Noise Pixel Range < NSRANGEY > / <NSRANGEUV> 0 ~ 2 1 –
– 1 Noise Region 0 < NSRGIONY0 > / <NSRGIONUV0> 0 ~ 1023 12 –
– 2 Noise Region 1 < NSRGIONY1 > / <NSRGIONUV1> 0 ~ 1023 24 –
– 3 Noise Region 2 < NSRGIONY2 > / <NSRGIONUV2> 0 ~ 1023 40 –
– 4 Noise Gain Level < NSFILTERY** > / <NSFILTERUV**> 0 ~ 255 50 –
S 714 – Noise Reduction Enable N.R OFF
– 0 Noise Level < NOISELEVEL > 0 ~ 1023 0 –
S 715 – Noise Reduction Only Enable N.R OFF
– 0 Noise Pixel Range < NSRANGEY > / <NSRANGEUV> 0 ~ 2 1 –
– 1 Noise Region 0 < NSRGIONY0 > / <NSRGIONUV0> 0 ~ 1023 12 –
– 2 Noise Region 1 < NSRGIONY1 > / <NSRGIONUV1> 0 ~ 1023 24 –
Group
No.
Data
Range
Initial Value
Function
Item
No.
Item
PLC-XF47
To Next Page
Loading...
