To Next Page
J
Jon WhitneyAug 29, 2025
How to fix dim print images on my SATO Label Maker?
- JjeffreyhaynesAug 29, 2025
If the SATO Label Maker displays dim print images, adjust the darkness level setting to increase the print head darkness.
How to fix dim print images on my SATO Label Maker?
If the SATO Label Maker displays dim print images, adjust the darkness level setting to increase the print head darkness.
What to do if my SATO Label Maker displays a ribbon end error?
If your SATO Label Maker displays a 'Ribbon end' error, it means the ribbon is either out or ripped, or it's not set properly. To fix this, ensure you set the ribbon correctly.
What to do if my SATO Label Maker shows a paper end error?
If your SATO Label Maker runs out of paper, set the paper properly.
What causes a 'Sensor error' on a SATO CG412TT and how do I fix it?
A 'Sensor error' on your SATO Printer can be due to a wrong sensor level, wrong sensor type, too big a value set for pitch offset, or label meandering. Adjust the level, adjust the sensor type, or set a smaller value for the pitch offset.
What to do if my SATO CG412TT labels are not dispensed?
If labels are not dispensed from your SATO Printer: Set dispenser unit correctly Clean the Dispensing roller and Platen roller.
What to do if my SATO Printer shows 'Ribbon near end'?
If your SATO Printer displays 'Ribbon near end', it indicates that there is not much ribbon left. Replace the ribbon to resolve this issue.
What to do if my SATO CG412TT is not feeding media?
To address the issue of your SATO Printer not feeding media: Set media correctly, Set the sensor correctly by Utility Tool setting Check the connection of sensor cable. Adjust sensor level Clean the platen roller.
What to do if my SATO Printer shows 'Paper end' error?
If your SATO Printer displays a 'Paper end' error, it means the printer is out of paper. To resolve this, set the paper properly.
What causes a 'Download error' on my SATO CG412TT Printer?
General| Print Method | Thermal Transfer / Direct Thermal |
|---|---|
| Operating System Compatibility | Windows, Linux |
| Print Resolution | 305 dpi |
| Maximum Print Width | 4.1 inches (104 mm) |
| Maximum Print Length | 999 mm |
| Media Type | Roll |
| Media Width | 0.87 inches (22 mm) to 4.57 inches (116 mm) |
| Media Thickness | 0.06 mm - 0.25 mm |
| Media Roll Diameter | 127 mm (5 inches) |
| Interfaces | USB, Serial, Ethernet |
| Supported Barcode Types | QR Code |
| Power Requirements | AC 100-240V, 50/60 Hz |
| Print Speed | Up to 4 ips (100 mm/sec) |
| Ribbon Width | 1.3 inches (33 mm) to 4.5 inches (114 mm) |
Explains symbols used for safety instructions in the manual.
Guidelines for choosing a suitable environment and placement for the printer.
Requirements and recommendations for connecting the printer to a power source.
Highlights the key features and capabilities of the CG4 Series printer.
Instructions for safely removing the printer from its packaging.
Identifies and describes the various parts of the printer.
Recommendations for placing the printer in a suitable environment.
Guidance on choosing the correct type and size of labels or paper.
Step-by-step instructions for loading different types of media into the printer.
Procedure for loading the carbon ribbon for thermal transfer printing.
Explains how to connect the printer to a host computer and power source.
Describes the buttons and LED indicators on the printer's operator panel.
Overview of the various operating modes available for the printer.
How to perform a test print for diagnostic purposes.
Procedure for running factory-level test prints.
Guide to configuring various printer settings and functions.
Explains error signals and their causes and corrective actions.
A table listing common printer issues and their recommended solutions.
Steps to troubleshoot problems related to printer interfaces (USB, RS232C, LAN).
Instructions on cleaning the printer's print head, platen roller, and other parts.
Detailed steps for cleaning the printer using a cleaning kit.
Instructions for cleaning the print head using a cleaning sheet.
Guide on how to replace user-replaceable parts like the print head and platen roller.
How to adjust print darkness and speed for optimal print quality.
Physical, power, environmental, and print specifications of the printer.
Details on compatible media types, sizes, and thicknesses.
Specifications for ribbon types, dimensions, and usage.
Information on operation keys, indicators, and surface treatment.
Lists available optional accessories for the printer.
Lists the different interface types available for the CG4 Series printers.
Detailed specifications and settings for the RS232C serial interface.
Detailed specifications and pin assignments for the IEEE 1284 parallel interface.
Specifications and pin assignments for the USB interface.
Specifications and configuration for the LAN Ethernet interface.
Details on the installation and use of the optional cutter accessory.
Instructions for installing and using the optional dispenser accessory.
Diagram showing the locations of sensors and optional accessories on the printer.
Explains the differences between various printer operation modes.
Defines the base reference point for print and cut positions in different modes.
How to adjust the offset position for cutting, dispensing, or tear-off.
Describes printer behavior when the end of the label roll is detected.
Describes printer behavior when the ribbon is nearing or at its end.
Contact information for various SATO offices and subsidiaries globally.
