What to do if my SATO CG408TT Printer is not dispensing linerless labels?
If your SATO Printer is not dispensing linerless labels: Set Linerless (Non sepa) unit correctly Clean the Linerless platen roller.
What to do if my SATO CG408TT displays 'Ribbon end' error?
If your SATO Printer shows a 'Ribbon end' error, it means that the printer is either out of ribbon or the ribbon is ripped, or the ribbon is not set properly. To fix this, set the ribbon properly.
What to do if my SATO CG408TT Printer is not feeding media?
To address the issue of your SATO Printer not feeding media: Set media correctly, Set the sensor correctly by Utility Tool setting Check the connection of sensor cable. Adjust sensor level Clean the platen roller.
What causes a machine error on my SATO Label Maker?
If the SATO Label Maker shows a machine error caused by a board defect, board replacement is required.
What to do if my SATO Printer displays 'Cutter error'?
If your SATO Printer shows a 'Cutter error', it could mean the cutter is not connected or the cut operation failed. Connect the cutter unit, or set and feed the paper again.
What does 'Calendar error' mean on my SATO CG408TT Printer?
A 'Calendar error' on your SATO Printer means that wrong date/time data is read from calendar IC. Check to see if calendar IC is installed or not and consider board replacement.
How to resolve incorrect label sensor selection on my SATO Label Maker?
If you have incorrect label sensor selection on your SATO Label Maker, set the sensor correctly by printer setting tool.
What to do if my SATO CG408TT Printer cover is open?
If you receive a 'Cover open' error on your SATO Printer, it indicates that the cover is not closed properly. Make sure to close the cover completely.
What to do if the print head of my SATO Label Maker is defective?
If the print head of your SATO Label Maker is defective, replace print head as required.
What to do if my SATO Label Maker displays a buffer over error?
If your SATO Label Maker shows a 'Buffer over' error, it means the amount of data received exceeds the limit of the receive buffer, or the protocol is wrong. Correct the software on the host side or set the correct protocol to resolve this.
Explains pictographic symbols used in the manual and on the printer for safety.
Guidelines for choosing an appropriate and safe location for the printer.
Instructions and considerations for connecting the printer to a power source.
Lists the key features and capabilities of the CG4 Series printer.
Instructions for unpacking the printer and identifying included accessories.
Identifies and labels the main components of the printer's front and back views.
Guidance on selecting an appropriate location and choosing the correct media for the printer.
Step-by-step guides for loading roll media and carbon ribbon into the printer.
Guides on connecting power cables and various interface types for the printer.
Details the buttons and LED indicators on the printer's front panel.
Explains the different operational modes of the printer and how to access them.
Instructions for User and Factory Test Print modes for diagnostics.
Covers Operation Setting, Download, Default, and HEX Dump modes.
Lists various printer settings and their default values or ranges.
Interprets printer error signals (LEDs, buzzer) to diagnose problems.
Provides common printer problems and their potential solutions.
Guides on troubleshooting interface issues and using test prints for diagnostics.
Detailed instructions for cleaning the print head, platen, rollers, and using cleaning kits/sheets.
Information on how to easily replace the print head and platen roller.
How to optimize print quality via darkness and speed settings.
Lists physical, power, environmental, and print specifications for the CG4 Series.
Specifications for optional cutter, dispenser, and linerless kits.
Details the different interface types available for the CG4 Series printers.
Specifications and communication settings for the RS232C serial interface.
Specifications and pin assignments for the IEEE 1284 parallel interface.
Specifications and pin assignments for USB and LAN interfaces.
Details on optional cutter, dispenser, and their installation/usage.
Covers sensor positions, operation modes, reference points, and offset adjustments.
Describes printer behavior when paper or ribbon runs out.
Lists contact information for SATO worldwide operations.
General| Print Method | Thermal Transfer / Direct Thermal |
|---|---|
| Resolution | 203 dpi |
| Max Print Width | 104 mm |
| Memory | 8MB Flash ROM, 16MB SDRAM |
| Print Speed | 4 ips |
| Media Sensor | Reflective and Transmissive |
| Interface | USB, RS232C |
| Optional Interfaces | Ethernet |
| Media Type | Roll, Fanfold |
| Media Width | 22 mm to 118 mm |
| Media Thickness | 0.06 mm - 0.2 mm |
| Ribbon Width | 40 mm to 110 mm |
| Power Supply | AC 100-240V, 50/60 Hz |
To Next Page
