What to do if Sceptre monitor screen says no signal?
First, ensure you've selected the correct source on your Sceptre monitor, and check all available sources. Inspect your video cable for damage and try swapping it with a new one. Also, verify that the power plug is securely connected to both the monitor and the wall outlet.
How do I reset my Sceptre E20 Monitor to factory settings?
To reset your Sceptre monitor to its factory default settings, open the OSD (On-Screen Display) menu. Look for the 'OTHER' options and select 'RESET'. This will restore all settings to their original factory values.
What to do if my Sceptre E20 Monitor says 'Signal Out of Range'?
If your Sceptre monitor displays 'SIGNAL OUT OF RANGE', and you previously used a CRT monitor, connect the CRT monitor and reduce the refresh rate to 60 Hz in your video card's display settings. If you don't have a CRT monitor or it's broken, turn off both the LED monitor and your computer. Then, turn them back on and continuously press the 'F8' key until a selection menu appears. Select 'Safe Mode', uninstall any video card and monitor drivers using 'Add / Remove Programs' or 'System Properties'. Reboot your computer, install the monitor driver first, then the video card driver, ensuring the refresh rate is at 60Hz.
Why I do not hear any sound from the speakers when using the HDMI port on my Sceptre E20?
If your Sceptre monitor isn't producing any sound through the HDMI port, ensure that your video device's audio output is set to HDMI and is transmitting PCM sound format, as the monitor only decodes PCM signals.
What to do if Sceptre Monitor screen says no video or no signal?
To resolve a 'no video' or 'no signal' message on your Sceptre monitor, first, inspect the video cable for any damage and try swapping it with a new one. Next, check that the power plug is securely connected to both the monitor and the wall. Finally, ensure your computer is powered on.
Why I do not hear any sound from the speakers on my Sceptre Monitor?
If you cannot hear any sound from the speakers on your Sceptre monitor, check the 3.5 mm mini-jack cable connection between your computer and the monitor. Also, verify the volume levels on both your computer and the monitor.
How do I reset my Sceptre E20 Monitor?
To reset your Sceptre monitor, ensure there's a valid video signal, then press the menu button to access the OSD. Look for the RESET option.
Why is my Sceptre E20 saying “Signal Out of Range”?
The “Signal Out of Range” message on your Sceptre monitor typically indicates an incompatible refresh rate. If you have a CRT monitor, connect it to your computer and lower the refresh rate to 60 Hz through your video card's display settings. If you don't have a CRT monitor or it's broken, turn off both the LED monitor and your computer. Then, turn them back on and continuously press the “F8” key until a selection menu appears. Select “Safe Mode,” uninstall any video card and monitor drivers via “Add / Remove Programs” or “System Properties,” and reboot your computer. After rebooting, install your monitor driver first, followed by your video card driver, ensuring the refresh rate is set to 60Hz.
Why are the words and video too blurry on my Sceptre E20 Monitor?
If the words and video appear blurry on your Sceptre monitor, ensure you are using the monitor's native resolution of 1600 x 900 at 60 Hz. If the issue persists, try enabling or disabling the CLEAR TYPE function in Windows.
What to do if the video is too bright on my Sceptre E20 Monitor?
If the video on your Sceptre monitor is too bright, especially with older video cards, try lowering the contrast and adjusting the brightness to compensate. This issue might occur because newer LEDs are designed for HD video and may not be fully compatible with older video cards.
General| Screen Size | 20 inches |
|---|---|
| Resolution | 1600 x 900 |
| Aspect Ratio | 16:9 |
| Panel Type | TN |
| Brightness | 250 cd/m² |
| Contrast Ratio | 1000:1 |
| Response Time | 5 ms |
| Refresh Rate | 60Hz |
| Viewing Angle | 170° (H) / 160° (V) |
| Input Connectors | HDMI, VGA |
| Ports | VGA, HDMI |
To Next Page
