EasyManua.ls Logo

Sceptre E20 - User Manual

Sceptre E20
35 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
- 1 -
www.SCEPTRE.com
SCEPTRE E20 Display User Manual
SAFETY INSTRUCTIONS
Electricity is used to perform many useful functions, but it can also cause personal
injuries and property damage if improperly handled. This product has been engineered
and manufactured with the highest priority on safety. However, improper use can result
in electric shock and / or fire. In order to prevent potential danger, please observe the
following instructions when installing, operating and cleaning the product. To ensure
your safety and prolong the service life of your Liquid Crystal Display, please read the
following precautions carefully before using the product.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves,
or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and a third grounding prong. The wide blade and
the third prong are provided for your safety. If the provided plug does not fit
into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at the
plugs, convenience receptacles, and the point where they exit from the
apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury
from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long
periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when
the apparatus has been damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.

Table of Contents

Other manuals for Sceptre E20

Preview: Manual
Manual32 pages

Questions and Answers

  • J
    John AllenSep 23, 2025
    Why is Auto Adjust grayed out on my Sceptre E20?
    • S
      Stefanie ChangSep 23, 2025
      The AUTO ADJUST function is grayed out on your Sceptre monitor because it is only available when using a VGA video connection. This option is disabled for HDMI connections, as it is designed for adjusting analog signals.
  • A
    Anthony GutierrezAug 23, 2025
    How do I reset my Sceptre E20 Monitor to factory settings?
    • J
      Jessica HarperAug 25, 2025
      To reset your Sceptre monitor to its factory default settings, open the OSD (On-Screen Display) menu. Look for the 'OTHER' options and select 'RESET'. This will restore all settings to their original factory values.
  • T
    Travis MossAug 25, 2025
    What to do if my Sceptre E20 Monitor says 'Signal Out of Range'?
    • S
      Samantha BauerAug 26, 2025
      If your Sceptre monitor displays 'SIGNAL OUT OF RANGE', and you previously used a CRT monitor, connect the CRT monitor and reduce the refresh rate to 60 Hz in your video card's display settings. If you don't have a CRT monitor or it's broken, turn off both the LED monitor and your computer. Then, turn them back on and continuously press the 'F8' key until a selection menu appears. Select 'Safe Mode', uninstall any video card and monitor drivers using 'Add / Remove Programs' or 'System Properties'. Reboot your computer, install the monitor driver first, then the video card driver, ensuring the refresh rate is at 60Hz.
  • R
    Rebecca SimpsonAug 27, 2025
    Why I do not hear any sound from the speakers when using the HDMI port on my Sceptre E20?
    • D
      danielpruittAug 27, 2025
      If your Sceptre monitor isn't producing any sound through the HDMI port, ensure that your video device's audio output is set to HDMI and is transmitting PCM sound format, as the monitor only decodes PCM signals.
  • J
    jeremy61Aug 27, 2025
    What to do if Sceptre Monitor screen says no video or no signal?
    • J
      Joanna GibsonAug 27, 2025
      To resolve a 'no video' or 'no signal' message on your Sceptre monitor, first, inspect the video cable for any damage and try swapping it with a new one. Next, check that the power plug is securely connected to both the monitor and the wall. Finally, ensure your computer is powered on.
  • T
    Tim TaylorSep 18, 2025
    Why are the colors not correct on my Sceptre E20?
    • G
      garyperkinsSep 18, 2025
      If the colors on your Sceptre monitor are not displaying correctly, the VGA or HDMI cable might be loose or damaged. Try reconnecting the cable or replacing it with a different one to see if the issue is resolved.
  • R
    Riley BellSep 13, 2025
    What to do if the colors are not correct on Sceptre E20?
    • M
      Mackenzie DaySep 13, 2025
      If the colors on your Sceptre monitor are not displaying correctly, the DVI, DP, or HDMI cable might be loose or damaged. Try reconnecting the cable or replacing it to see if the problem is resolved.
  • C
    cameron57Sep 16, 2025
    How to make words bigger on Sceptre E20?
    • R
      Rebecca MartinSep 16, 2025
      If the words appear too small on your Sceptre monitor at a resolution of 1600x900, you can adjust the text size within your Windows operating system display properties. For Windows XP: Right-click on the background, select PROPERTIES, go to the SETTINGS tab, click ADVANCED, and under the GENERAL tab, change the word size from NORMAL SIZE to LARGE SIZE. For Windows 7-10: Right-click on the wallpaper, select PERSONALIZE, click ADJUST FONT SIZE (DPI), then CONTINUE. Change the text size from DEFAULT SCALE to LARGE SCALE. Remember to reboot your computer after applying these changes.
  • S
    Sherry BerrySep 5, 2025
    How to fix unclear display on Sceptre Monitor?
    • B
      Brett NormanSep 6, 2025
      If your Sceptre monitor's display is unclear and unstable when using VGA, use the AUTO ADJUST function or set the resolution to the optimal setting of 1600x900 at 60Hz, then use AUTO ADJUST. If you are using HDMI, ensure your resolution is set to 1600x900; other resolutions may appear blurry.
  • J
    Jeremy ElliottSep 3, 2025
    What to do if the video is too bright on my Sceptre E20 Monitor?
    • A
      Alex BradleySep 3, 2025
      If the video on your Sceptre monitor is too bright, especially with older video cards, try lowering the contrast and adjusting the brightness to compensate. This issue might occur because newer LEDs are designed for HD video and may not be fully compatible with older video cards.

Summary

SAFETY INSTRUCTIONS

IMPORTANT INFORMATION

Installation

Assembling the Stand

Disassembling the Stand for Wall Mounting

Connections

On Screen Display (OSD) Menu

Quick Start Menu

Overview of the Quick Start menu options for common adjustments.

Picture Settings

Details various picture adjustments available in the OSD menu.

Color Settings

Explains color temperature, gamma, tint, and saturation adjustments.

System Settings

Troubleshooting

Specifications

Sceptre E20 Specifications

General IconGeneral
Screen Size20 inches
Resolution1600 x 900
Aspect Ratio16:9
Panel TypeTN
Brightness250 cd/m²
Contrast Ratio1000:1
Response Time5 ms
Refresh Rate60Hz
Viewing Angle170° (H) / 160° (V)
Input ConnectorsHDMI, VGA
PortsVGA, HDMI

Related product manuals