Scheppach HM216SPX Manual

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
30
|
GB
8.2.1 Connection to an external dust extractor
• Connect the vacuum hose with the dust extraction
spout.
• The industrial vacuum cleaner must be suitable for
the material being worked.
• -
tal to health or carcinogenic, use a special vacuum
cleaner.
8.3 Precision adjustment of the stop for crosscut
90° (g. 1/2/5/6)
Tools required:
- 
- Open-ended spanner SW13 (not included in the

• No stop angle included.
• Lower the machine head (4) and secure it using the
locking bolt (23).
• Loosen the set screw (22).
• Position the angle stop (A) between the saw blade

• Loosen the lock nut (26a).
• Adjust the adjusting screw (26) until the angle be-

• Tighten the lock nut (26a) again.
• -

Phillips screwdriver, set to position 0° on the angle
scale (18) and re-tighten the retaining screw.
8.4 Precision adjustment of the stop for mitre cut
45° (g. 1/2/5/9/10)
Tools required:
- 
- Open-ended spanner SW13 (not included in the

• No stop angle included.
• Lower the machine head (4) and secure it using the
locking bolt (23).
• 
Attention!
For bevel cuts (inclined saw head), the moveable

(Left side).
• Open the set screw (16b) for the moveable stop rail
(16a) and push the moveable stop rail (16a) out-
wards.
• The moveable stop rails (16a) must be locked so
that the distance between the stop rails (16a) and
the saw blade (6) is at least 8 mm.
• -
ner position. (Right side).
• Before making a cut, check that the stop rail (16a)
and the saw blade (6) cannot collide.
• Loosen the set screw (22) and use the handle (1) to
angle the machine head (4) 45° to the left.
•        

identical to the mains data.
7.1 Checking the moving saw blade guard safety
device (5)
The saw blade guard protects against accidental con-

Check function
To do so, fold the saw downwards:
• The saw blade guard must provide free access to
the saw blade without touching other parts.
• When folding the saw upwards into the starting
position, the saw blade guard must cover the saw

8. Attachment
8.1 Attaching the crosscut, drag and mitre saw
(g. 1/2/4)
• 
  

• -
sired angle measurement on the scale (13) and use
the handle (11) to secure it.
• 

time, pulling out and turning the locking pin (23)
from the engine mount.
• Turn the locking bolt (23) 90 degrees to secure it in
the unlocked position.
• Swing the machine head (4) up.
• It is possible to secure the clamping devices (7) to

clamping devices (7) in the holes on the rear side
of the stop rail (16) and secure it with the star grip
screws (7a). For 0°- 45° mitre cuts, the clamping


• It is possible to tilt the machine head (4) a max. 45°

•       
and used during work. Set the desired table size

screw (9) again.
8.2 Sawdust bag (g. 1/22)
The saw is equipped with a debris bag (17) for saw-
dust and chips.
Squeeze the wings of the metal ring on the dust bag
(17) together and slide it over the discharge port near
the engine.
 
zipper at the bottom.

Scheppach HM216SPX Specifications

General

Brand	Scheppach
Model	HM216SPX
Category	Saw
Language	English