To Next PageTo Next PageWhat to do if Scheppach sd1600v blades break?
If the saw blades on your Scheppach Saw are breaking, it could be due to several factors. First, check if the tension is incorrectly set and adjust it to the correct setting. Second, reduce the load by feeding the workpiece more slowly. Third, ensure you are using the correct saw blade variety. Finally, avoid exerting pressure from the side to ensure the workpiece is fed straight.
How to fix a Scheppach sd1600v Saw blade that oscillates and isn't aligned straight?
If the saw blade oscillates and isn't aligned straight, the holders may not be aligned. To fix this, open the screws that fasten the holders, bring the holders into the vertical position, and tighten the screws again.
Why does my Scheppach Saw vibrate?
Vibration in your Scheppach Saw can occur due to several reasons. It may be due to incorrect installation. Refer to the instructions in the manual for proper installation. An unsuitable underlay can also cause vibration; a heavier workbench reduces vibration, with solid wood being better than plywood. Ensure the workbench is not resting on the motor and is securely screwed down. Tighten the locking lever. Also, make sure the motor is securely screwed in place.
What to do if my Scheppach Saw motor does not function?
If the motor of your Scheppach Saw isn't working, it may be due to a faulty mains cable. Replace the faulty parts. If the motor itself is faulty, contact customer service for assistance. Do not attempt to repair the motor yourself; this should be done by trained personnel.
How to fix Scheppach sd1600v Saw blade swinging out?
If the saw blade swings out on your Scheppach Saw, it's likely that the holders are not aligned straight. To fix this, loosen the screws that fasten the holders to the arm. Align the holders so they are perpendicular to each other, and then retighten the screws.
Why won't my Scheppach sd1600v Saw motor start?
There are several reasons why the motor of your Scheppach Saw might not be starting: * The mains fuse may have blown: Check the mains fuse. * The extension cable could be defective: Replace the extension lead. * The fine-wire fuse may be defective: Check the fine-wire fuse and replace it with a fuse of the same type if needed. * There might be a connection issue to the motor or switch: Have this checked by an electrician. * The motor or switch itself could be faulty: Have this checked by an electrician.
How to fix Scheppach sd1600v blade oscillating?
If the saw blade of your Scheppach Saw is oscillating and not aligned straight, the holders may not be aligned properly. To fix this, open the screws that fasten the holders, bring the holders into the vertical position, and then tighten the screws again.
Why does the Scheppach sd1600v Saw blade loosen after switching off?
If the saw blade without pins on your Scheppach Saw loosens after switching off the engine, it might be because the saw blade clamping screw (27/28) is not tightened enough. Tighten the saw blade clamping screw (27/28) to resolve this issue.
Why do Scheppach sd1600v blades break?
Saw blades may break due to several reasons: * Incorrect tension: Ensure you set the correct tension. * Excessive load: Reduce the feed rate of the workpiece. * Incompatible saw blade: Use the correct saw blades for your material. * Improper feeding: Avoid applying side pressure to the workpiece.
General| Blade length | 134 mm |
|---|---|
| Throat depth | 406 mm |
| Product color | Black, Blue |
| Stroke height | 50 mm |
| Idle speed (max) | 1700 RPM |
| Idle speed (min) | 500 RPM |
| Table tilt range | 0 - 45 ° |
| Maximum power | 120 W |
| AC input voltage | 220-240 V |
| AC input frequency | 50 Hz |
Weight and Dimensions| Depth | 630 mm |
|---|---|
| Width | 295 mm |
| Height | 370 mm |
| Weight | 12700 g |
| Table depth | 415 mm |
| Table width | 255 mm |
