Sharp AR-5127 - System Configuration

AR-5127 SYSTEM CONFIGURATION 2 - 1
[2] SYSTEM CONFIGURATION
1. Structure
A. Hardware
Block diagram
Mirror-Motor
SFP/RSPF Unit (
Optional)
Down-Load-CON D-Sub 9pin
SPF-SEN-PWB SPF Cover Sens SPF-PSOL SPF PS Sens SPF Paper Empty
SPF Paper Size Sens
(x5) Scanner Mirror HP
SPF BOOK Sens Cover Sensor
L1 Sensor
D-Sub 25pin D-Sub 15pin
L2
Defog Heater
Paper Size Sensor
CCD-PWB
AB INCH
SPF-Motor
SPF-DupSOL
Shifter HP Sensor
Fuser Cooling Fan 1
CN118
CN108
CN117
Pout Sensor
Fuser Cooling Fan 2
Shifter-Motor
CN104
(AR5127 Optional)
CN103
Duplex-Motor
(AR5127 Optional)
Main body cassette unit
Duplex Paper Out
CN129
Sensor
PAP1H ; Paper Empty LUD1H ; Lift Up Detector Paper Remove
PPD1H(PIN):Paper IN Sol PCS1H ; Pick Up Solenoid Drum Initial
CN140
Sensor (AR5127 Optional)
2nd cassette unit (Optional)
CSS2H ; Casette Detector
OP interface PWB
DRS2H ; Door Detector PPD2H ; Paper Pass Detector PAP2H ; Paper Empty LUD2H ; Lift Up Detector PCL2H ; Pick Up Clutch LUM2H ; Lift Up Motor
CN126
TRCLH ; Vertical transport roller clutch
Multi-step cassette unit (Optional)
Defog Heater
OP interface PWB
Japan/SEC/SECL
HPEMPTY :
HandpaperEmpty sensor
Paper Feed Motor HPIN : Handpaper IN Sensor
HPTRAY1 :
HandpaperTRAY Sensor
MAIN-Motor
DEV
InterLock
Power Unit
Ozon Fan
OP-UP cassette OP-LO cassette HPTRAY2 :
HandpaperTRAY Sensor2
Coin
UNIT
Toner-Motor Switch
PPD1 ;
Paper Pass Detector
PPD2 ;
Paper Pass Detector
HPSIZE : Handpaper Size Sensor Vender
(include CRSM)
PAP1 ; Paper Empty
PAP2 ; Paper Empty HPSIZE2 : Handpaper Size Sensor2
LUD1 ; Lift Up Detector
LUD2 ; Lift Up Detector HPWS : Handpaper Width Sensor OPERATION PANEL
Polygon-Motor
Power Supply
PS Cooling Fan
CSS1 ; Casette Detector
CSS2 ; Casette Detector HPSOL :
Handpaper PickUp Solenoid
HVU
DRS1 ; Door Detector
DRS2 ; Door Detector
LCD
PS-SW
PCL1 ; Pick Up Clutch
PCL2 ; Pick Up Clutch CSS1H : Cassette Detector
LUM1 ; Lift Up Motor
LUM2 ; Lift Up Motor PSRSOL : Paper Stop Roller Sol.
Reactor
PCL1H : PickUp Cluth
FAX-OP-PWB
LSU-PWB
CE Only
LUM1H : Lift Up Motor COPY-OP-PWB
APC-PWB
BD-PWB
Fuser Unit BD-Sensor
THERMISTER
CN123
CN131
(AB Area ONLY)
CN139
CN132
CN130
Pout Gate
Solenoid
SPF-CON-PWB
Pout 2 Sensor
TRAYPAPER SENSOR
(INCH Area ONLY)
CN106
FAX PWB
CN112
CN110
CN121
CN109
Finisher Unit (Optional)
FINISHER PWB
MCU-PWB
Option interface PWB
GDI PWB
Mother PWB
CN115
CN135
CN102
CN111
CN136
CN28
CN134
CN107
CN113
2nd POUT COVER
SENSOR
CN125
IMC PWB
Paper Full Sensor
Copy-Lamp
Fuser-Lamp
SPF-pressure release SOL
Paper Feed Motor
TRCL ; Vertical transport
roller clutch 2
Manual feed unit
Main body paper feed load
USB PWB
(AR5127 Optional)
Staple empty sensor Stapler Cartridge empty sensor
Paper Size Detector
Staple operation motor
Staple supply cover open/close sensor
Rear edge plate HP sensor
Staple HP sensor
Side guide plate HP sensor
Tray JAM process sensor
Tray paper empty sensor
JAM process PG open/close sensor
Self priming sensor No. 1 tray paper exit sensor
Side guide plate motor
Rear edge plate drive solenoid
No. 2 tray paper exit sensor
Rear edge plate drive motor
Transport select gate right solenoid
Lift-up drive control sensor
Upper alignment plate drive solenoid
Tray position sensor Upper
FIN main motor
Transport select gate right solenoid 2
Paper position sensor
Tray lift-up motor
Shutter drive solenoid
Tray position sensor Lower
Tray off-set motor
Paper exit roller clutch
Off-set position sensor