Sharp AR-M276

AR-M236/M276/M237/M277 SIMULATION 8 - 46
The output image is remained even after outputting.
Note: Executable only when the FAX is installed.
Operation/procedure
Select the message number with the 10-key, and press the [START]
key.
By setting the message No., the sound message is sent to the line and
the speaker of the body. (The message is repeated until the interrup-
tion command is provided by pressing the [CUSTOM SETTINGS] key.)
By pressing the [START] key during execution, the signal kind can be
changed.
Message No. 5 can be heard by an external telephone speaker.
Note: Executable only when the FAX is installed.
Operation/procedure
Select the message number with the 10-key, and press the [START]
key.
By setting the message No., the sound message is sent to the line and
the speaker of the body. (The message is repeated until the interrup-
tion command is provided by pressing the [CUSTOM SETTINGS] key.)
By pressing the [START] key during execution, the signal kind can be
changed.
Message No. 5 can be heard by an external telephone speaker.
Note: Executable only when the FAX is installed.
Operation/procedure
Select "1: YES" with the 10-key and press the [START] key. (When "2:
NO" is selected, the simulation is canceled.)
Used to clear all image data (including confidential reception data)
stored in image memory of the FAX section.
The management table is also cleared (initialized) at the same time.
* lIf there is any print data, the power must be turned off after clearing.
Note: Executable only when the FAX is installed.
Operation/procedure
Select the signal number with the 10-key, and press the [START] key.
By setting the signal number, the specified signal is delivered to the
line at the speed of 300bps. (The signal is continuously sent until the
interruption command is provided by pressing the [CUSTOM SET-
TINGS] key.)
The signal send level can be selected from 0dB or the soft SW set
value.
The signal send level is returned to the soft SW set value before exe-
cution of the mode after completion of the mode.
By entering the number and pressing the [START] key during execu-
tion, the signal kind can be changed.
66-8
Purpose Operation test/check
Function (Purpose) Voice Message send (Signal send level:
Max.) (Japan only)
Section FAX
Item Operation
Item Voice message
1NONE
Silent
2 FAX/TEL MSG1 "Hold the line a minute, please send fax."
(TEL/FAX voice response)
3 FAX/TEL MSG2 "Hold the line a minute."
(TEL/FAX voice response)
4 FAX/TEL MSG3 "Not around here, please send fax."
(TEL/FAX voice response)
5 CHANGED RX MSG "Ding Dong"
(Sound delivered when switching to remote
reception)
6 RINGER Call sound
7 EXT.TEL RINGER External telephone call
66-9
Purpose Operation test/check
Function
(Purpose)
Used to send the voice message. (Signal send level:
Set by soft SW.) (Japan only)
Section FAX
Item Operation
1
2
Item Voice message
1NONE
Silent
2 FAX/TEL MSG1 "Hold the line a minute, please send fax."
(TEL/FAX voice response)
3 FAX/TEL MSG2 "Hold the line a minute."
(TEL/FAX voice response)
4 FAX/TEL MSG3 "Not around here, please send fax."
(TEL/FAX voice response)
5 CHANGED RX MSG "Ding Dong"
(Sound delivered when switching to remote
reception)
6 RINGER Call sound
7 EXT.TEL RINGER External telephone call
66-10
Purpose Adjustment/Setting/Check
Function (Purpose) Image data memory clear
Section FAX
Item Data Image data
66-11
Purpose Operation test/check
Function
(Purpose)
Used to send 300bps signals. (Signal send level:
Max.)
Section FAX
Item Operation
2
1