[JOB#916] MRS = 0000
#916-A, B: Not used (Fixed at "00")
#916-C: 1. Negative merchandise subtotal
2. Subtotal entry compulsory before tendering
3. Subtotal entry before direct non-tendering finalization
1. Negative
merchan-
dise
subtotal
2. Subtotal entry
compulsory
before
tendering
3 .Subtotal entry
before direct
non-tendering
finalization
916-C
Allow
Non-compulsory
Non-compulsory 0 ★
Compulsory 1
Compulsory
Non-compulsory 2
Compulsory 3
Disallow
Non-compulsory
Non-compulsory 4
Compulsory 5
Compulsory
Non-compulsory 6
Compulsory 7
#916-D: 1. Coupon PLU printing on X/Z report
2. Net sales subtotal (NET1) printing on X/Z report
3. CHECK change total printing on X/Z report
1. Print coupon
PLU’s on
general report
2. Print net
sales SBTL
(NET1) on
general report
3. Print CHK
CHANGE on
general report
916-D
Print
Print
Print 0 ★
Skip 1
Skip
Print 2
Skip 3
Skip
Print
Print 4
Skip 5
Skip
Print 6
Skip 7
[JOB#917] NOT USED MRS = 0000
[JOB#918] MRS = 0000
#918-A: 1. Dirrect non-tendering finalization after previous tender
entry
1. Dirrect non-tendering finalization after
previous tender entry
918-A
Disable 0
Enable 2 ★
#918-B, C, D: Not used (Fixed at "000")
[JOB#919] MRS = 0000
#919-A, B, C: Not used (Fixed at "000")
919-D: 1. Foreign currency format
1. Foreign currency 919-D
Not 0 ★
Omit digits lower than TAB position 1
[JOB#927] MRS = 0000
#927-A: 1. Rounding up of the units digit of amount
#927-B: 1. Rounding down of the units digit of amount
1. Rounding the units digit of amount 927-AB
Common destination 00 ★
Netherland/Switzerland 82
Norway 54
#927-C: 1. Difference memory (Difference between before-round-
ing and after-rounding)
2. Limit on the least sighificant digit in entering the amount
on item
1. Difference memory 2. Limit on the least
sighificant digit in
entering the amount on
item
927-C
No
Arbitary 0 ★
0 only 1
0 and 5 only 2
Yes
Arbitary 4
0 only 5
0 and 5 only 6
#927-D: 1. Application of rounding
2. Limit on the least significant digit in entering the amount
of payment
1. Application of
rounding
2. Limit on the least
significant digit in
entering the amount of
payment
927-D
Item & Payment
Arbitary 0 ★
0 only 1
0 and 5 only 2
Payment
Arbitary 4
0 only 5
0 and 5 only 6
[JOB#930∼931] MRS = 0000
RESET REPORT COUNTER
JOB # Function
930 Z1 report counter
931 Z2 report counter
[JOB#942, 943, 969] MRS = 0000000000000
GT COUNTER PRESETTING
JOB # Function
942 GT2 (Positive GT)
943 GT3 (Negative GT)
969 TRAINING GT
Note: GT1 is obtained by the following calculation.
Equation: GT1=GT2-GT3
[JOB#950] MRS = STANDARD KEY LAYOUT
Free key layout (Except for department keys and direct PLU keys.)
XXX: Key No. = 17 ∼ 150
To Next Page
Loading...
Need help?
General
