Sharp LC-32LE700E User Manual

LC-32/40/46LE700E/RU/S,LU700E/S,LX700E/RU,LC-52LE700E/RU/S
5 – 3
5. List of adjustment process mode menu
The character string in brackets [ ] will appear as a page title in the adjustment process menu header.
Page Line Item Description Remarks (adjustment detail, etc.)
1/17
1 MAIN Version Main software version
2 BOOT Version BOOT Version.
3 Monitor Version Monitor software version
4 T-CON/H.264 Version T-CON/H.264 Version
5 CPLD Version CPLD Version.
6 LED T-CON Version LED T-CON Version
7 EQ DATA CHECKSUM Audio data checksum.
8 LAMP ERROR Number of termination due to lamp error.
9 MONITOR ERR CAUSE Last error standby cause.
10 NORMAL STANDBY CAUSE Situation that became standby at the end.
(Excluding the error)
11 ERROR STANDBY CAUSE Error standby cause
2/17
1 INDUSTRY INIT Enter Initialization to factory settings execution.
2 INDUSTRY INIT(-Hotel) OFF Initialization to factory settings execution.(Hotel mode is
excluded)
3 PUBLIC MODE OFF Hotel mode ON/OFF setting
4 Center Acutime 5H 0M Main operating hours.
5 RESET OFF Main operating hours reset.
6 Backlight Acutime 19H 35M Backlight operating hours.
7 RESET OFF Backlight operating hours reset.
8 LAMP ERROR RESET OFF Lamp error reset.
9 ADJ PARAM SET Enter ADJ PARAM SET
10 VIC XPOS 0 X-coordinate setting for VIC READ
11 VIC YPOS 0 Y-coordinate setting for VIC READ
12 VIC SIGNAL TYPE MAIN Signal type setting for VIC READ
13 VIC READ OFF Picture level acquisition function
(Level appears in green on the upper right)
3/17
1 RF AGC ADJ Enter RF-AGC auto adjustment execution
2 TUNER ADJ Enter TUNER auto adjustment execution
3 PAL+TUNER ADJ Enter PAL TUNER auto adjustment execution
4 RF AGC 16 RF-AGC auto adjustment execution (CA-8CH)
5 TUNER ADJ(SMPTE) Enter TUNER auto adjustment execution (SMPTE)
6 PAL+TUNER ADJ(SMPTE) Enter PAL TUNER auto adjustment execution (SMPTE)
TUNER ADJ(SMPTE CH57) Enter TUNER auto adjustment execution (SMPTE CH57)
7 PAL+TUNER ADJ(SMPTE CH57) Enter PAL TUNER auto adjustment execution (SMPTE CH57)
8 TUNER CONTRAST A_GAIN 14 TUNER signal level adjustment
9 TUNER CONTRAST D_GAIN 2048 TUNER signal level adjustment
10 TUNER CONTRAST OFFSET 256 TUNER signal level adjustment
11 RF AGC READ OFF Reading value of RF-AGC voltage
4/17
1 PAL ADJ Enter PAL adjustment
2 SECAM ADJ Enter SECAM adjustment
3 N358 ADJ Enter N358 adjustment
4 PAL CONTRAST A_GAIN 14 PAL contrast adjustment
5 PAL CONTRAST D_GAIN 2048 PAL contrast adjustment
6 PAL CONTRAST OFFSET 256 PAL contrast adjustment
7 SECAM CONTRAST A_GAIN 14 SECAM contrast adjustment
8 SECAM CONTRAST D_GAIN 2048 SECAM contrast adjustment
9 SECAM CONTRAST OFFSET 256 SECAM contrast adjustment
10 N358 CONTRAST A_GAIN 14 N358 contrast adjustment
11 N358 CONTRAST D_GAIN 2048 N358 contrast adjustment
12 N358 CONTRAST OFFSET 256 N358 contrast adjustment
5/17
1 HDMI CEC TEST Enter HDMI CEC test
2 INSPECT USB TERM Enter Reading inspection of USB memory terminal
3 HDMI EDID WRITE Enter HDMI EDID WRITING
4 MONIDATA READ[TEMP/OPC] OFF MONITOR Temperature/ OPC Acquisition tool.
5 CAUSE RESET Enter Reset of standby cause

Sharp LC-32LE700E Specifications

General

Display diagonal	32 \
Native aspect ratio	16:9
Native refresh rate	100 Hz
RMS rated power	20 W
Number of speakers	2
PC in (D-Sub)	Yes
HDMI ports quantity	4
USB 2.0 ports quantity	1

Weight and Dimensions

Depth (without stand)	92 mm
Width (without stand)	767 mm
Height (without stand)	502 mm
Weight (without stand)	13500 g