LC-32/40/46LE700E/RU/S,LU700E/S,LX700E/RU,LC-52LE700E/RU/S
5 – 12
12)Input fixed [INPUT MODE FIXED]
13)Speaker ON/OFF selection [LOUD SPEAKER]
14)Remote control path through [RC PATH THROUGH]
15)232C power ON control [232C POWON]
16)Hotel mode setting [HOTELMODE]
Option “VARIABLE” “FIXED”, “ACCTRL” or “AC/RCCTRL” (loop enabled)
Default VARIABLE
Function • VARIABLE
• FIXED
• AC CTRL
• AC/RC CTRL
: input mode is not fixed.
: when “INPUT MODESTART” is active, it is impossible to switch to another channel or input
: when “INPUT MODESTART” is active the unit starts at the input mode which is selected
when power is turned on in the case of the AC-ON only.
: when “INPUT MODESTART” is active
the unit starts at the input mode which is selected when power is turned on in any case
(AC->ON, remote control->ON, main utit's key->ON)
Disabled key in setting
to “FIXED”
CHANNEL ( / ), DIRECT CHANNEL buttons, FLASHBACK, INPUT SELECT,
TV/VIDEO, AUTO PRESET, MANUAL MEMORY,i.LINK,DIRECTINPUTSELECT,ATV,DTV,EPG,RADIO
Remarks • If [INPUT MODE START] is Normal, this function cannot be set. Set to “VARIABLE” automatically.
• In setting to “FIXED”
The channel setting and input selection in Menu are not displayed.
ON TIMER (Watching reservation) is not active.
Option “ON” or “OFF” (loop enabled)
Default ON
Function ON
OFF
: The sound from the speakers is output.
: The sound from the speakers is not output even if the headphones are not used.
Remarks • When the VOLUME UP/ DOWN key is pressed, the mute icon is displayed for 4 seconds.
• For the MUTE key and sound-related keys, caution is displayed.
• For the headphones and monitor output sound, normal operation is possible.
Option “OFF”, “ON:TVRCE” or “ON:TVRCD” (loop enabled)
Default OFF
Function The item decide whether the signal received by the remote control’s light-receiving section is output to the blank-
pin(9pin) of RS232C.
OFF
ON:TVRCE
ON:TVRCD
: this function is not active.
: this function is active, and remote control is active, too
: this function is active, but remote control is not active
Exception • In the case of “ON:TV RCD”, the start operation in the adjustment process mode,
inspection mode or hotel mode are enabled regardless of this setting.
• In the case of “ON: TV RCD", all the keys are enabled regardless of this setting.
while entering the adjustment process mode, inspection mode or hotel mode.
Remark There is case that the model can't always output due to the structure of the hardware.
Option “ENABLE” or “DISABLE” (loop enabled)
Default DISABLE
Function The item decide whether Power ON by the 232C command is enabled/disabled in the standby state.
The same function as 232C command “RSPW”.
ENABLE
DISABLE
: POWR0001 is always enabled.
: Start-up may be impossible at POWR0001.
( If the 232C command reception module isset to OFF, the command is invalid.)
Exception • In the case of “ON:TV RCD”, the start operation in the adjustment process mode,
inspection mode or hotel mode are enabled regardless of this setting.
• In the case of “ON: TV RCD", all the keys are enabled regardless of this setting.
while entering the adjustment process mode, inspection mode or hotel mode.
Remark There is case that the model can't always output due to the structure of the hardware.
Option “OFF” or “ON” (loopen abled)
Default OFF
Function The item decide whether hotel mode setting menu are enabled or disabled.
The same item as [HOTELMODE] in the adjustment process menu.
OFF
DISABLE
: Hotel mode is not active.
: ON.
Remark Each operation of the hotel mode is impossible unless this item is set to ON.
To Next Page
Loading...
Need help?
General
Weight and Dimensions
