MX-C250 SIMULATION 6 – 74
42 1 Data output during communication
error
0 : Output 1 : Not output
2 Memory overflow during receiving
data
0 : Output 1 : Not output
3 Received data duplex printing set-
ting (list)
0 : OFF 1 : ON
4 Duplex printing tray (Tray 1) 0 : OFF 1 : ON
5 Duplex printing tray (Tray 2) 0 : OFF 1 : ON
6 Duplex rotated printing 0 : ON 1 : OFF
7 - 8 Not used
43-
44
Not used
45 1 Simulated ring bell sounds 0 : Sound 1 : Not sound
2 FAX initial setting Digital line net setting 0 : OFF 1 : ON
3 Quick memory send setting display 0 : Displayed 1 : Not displayed
4 Manual send selection screen dis-
played
0 : Displayed 1 : Not displayed
5 - 8 Magnification setting in automatic
reduction
Setting range
0 - 15%
(100 - setting value)
46 1 Remote reception indication 0 : OFF 1 : ON
2 Remote changeover number set-
ting
0 : Only call-in 1 : Call-in/Call-out
3 Transfer function 0 : Prohibited 1 : Permitted
4 Specified number reception
Enable/Disable setting on manual
reception
0 : Ignore the specified num-
ber
1 : Reject the specified
number
5 Record of rejected reception 0 : Record 1 : Not record
6 Print in automatic reduction 0 : Prohibited 1 : Permitted
7 Priority order of the paper selec-
tion
0 : Priority area 1 : Priority width
8 Output way (Inch) when receiving
the A4 width image
0 : 210mm width printing 1 : 8.5inch width printing
47 1 Reception copy setting when
receiving the data
0 : Print out the copy when
receiving every one data
1 : Print out all copies after
receiving all copies
2 Report output (when cancelled) 0 : Output 1 : Not output
3 Report output (when refusing
reception)
0 : Output 1 : Convert name to the dial
number and print out
4 Address name of report conver-
sion
0 : Not convert 1 : Reject the specified
number
5 - 6 Range of the sound monitor Speaker is always off. 0 0
Speaker is on while dialing and
handshaking; off in data mode.
0 1
Speaker is always on. 1 0
Speaker is off while dialing; on
during handshaking and
retraining.
1 1
7 Control of the communication error
sound
0 : Sound 1 : Not sound
8 The communication error sound
when there is no response
0 : Sound 1 : Not sound
48 1 FAX initial setting Speaker volume after finishing
scanning (Small)
0 : Use volume 1 1 : Use volume 2
2 FAX initial setting Speaker volume after finishing
scanning (Middle)
0 : Use volume 2 1 : Use volume 3
3 FAX initial setting Speaker volume after finishing
scanning (Large)
0 : Use volume 3 1 : Use volume 4
4 FAX initial setting Speaker volume during DTMF
sending (Small)
0 : Use volume 1 1 : Use volume 2
5 FAX initial setting Speaker volume during DTMF
sending (Middle)
0 : Use volume 2 1 : Use volume 3
6 FAX initial setting Speaker volume during DTMF
sending (Large)
0 : Use volume 3 1 : Use volume 4
7 FAX initial setting Speaker volume of line monitor
(Small)
0 : Use volume 1 1 : Use volume 2
8 FAX initial setting Speaker volume of line monitor
(Middle)
0 : Use volume 2 1 : Use volume 3
SW
No.
Bit
No.
System set-
tings
Item SW selection and function Remarks
To Next Page
Loading...
Need help?
General
