To Next PageTo Next Page
Need help?Do you have a question about the Sharp VL-A10U and is the answer not in the manual?
Perform essential safety checks before returning the video camera to the user.
Warnings regarding electric shock, fire hazards, and proper handling of electrical components.
Visual identification of camcorder parts from front, rear, and bottom views.
Step-by-step instructions for disassembling the camcorder's camera section.
Detailed steps for disassembling the VCR main body of the camcorder.
Procedures for removing the VCR lid, AV unit, and AV unit cover.
Steps to disassemble the LCD holder assembly.
Steps for removing tilt unit, speaker, PWB, frame, and cassette compartment lid.
Detailed steps for disassembling the LCD panel assembly.
Precautions and preparation steps before replacing the CCD sensor.
Steps for removing and mounting the CCD sensor.
Lists jigs, tools, and parts required for mechanism checks and maintenance.
Schedule and points for periodic inspection and maintenance of the mechanism.
Important notes and cautions regarding maintenance procedures and parts.
Detailed procedures for checking and adjusting various mechanism functions.
Procedures to check/adjust reel disk height, take-up torque, and back tension torque.
Procedures to adjust tension pole position and rewind torque.
Preparation and adjustment steps for the mechanism's tape travel system.
Adjusting Tu guide, checking waveforms, and post-adjustment checks.
Explanation of mechanism modes and cassette control assembly procedures.
Disassembly procedures for the drum base, motor stator, and cassette control.
Installation of drum assembly, phase matching, and general assembling methods.
Detailed steps for assembling mechanism components like loading block and guide rails.
Final steps for assembling mechanism parts including drum, slide chassis, and levers.
Procedure for initial setting and data alteration of the E2PROM IC.
Adjustments for Y/C, audio, LCD, VCR, and VCR circuit adjustments.
Typical connections and required instruments for VCR section servicing.
Procedure for setting up the VCR section adjustment mode and navigating options.
Method for adjusting the battery shut-off voltage.
Procedure for adjusting the camcorder's power circuit.
Adjustments for system controller, servo circuit, and Y/C circuit.
Adjusting audio filter, checking audio, and adjusting LCD display circuits.
Adjusting VCO, H-position, Pulse, Bias, and White Balance for LCD.
Required tools, jigs, and connections for camera section servicing.
Step-by-step procedures for adjusting the camera section.
Adjusting power supply, auto focus, and camera signal parameters.
Adjusting white balance, color gain, and outdoor white balance.
Categorizes common troubles and suggests circuits to check.
Troubleshooting steps for camera issues and charging mode problems.
High-level block diagram of the camcorder's system.
Block diagrams for video signal, head amp, power, battery, and lens drive.
Comprehensive schematic diagram of the camcorder's overall circuitry.
Schematics for various circuits including ADC, DSP, Audio, Power, RF, Lens, Motor Driver, CCD, and more.
Identification of various semiconductor parts and their lead configurations.
Continued identification of semiconductor leads and part numbers.
Layout diagrams for the VCR Printed Wiring Board (Component and Wiring Sides).
Wiring layout diagrams for the VCR Printed Wiring Board (Side A).
Layout diagrams for the Camera Printed Wiring Board (Component and Wiring Sides).
Layout diagrams for the Head Amp Printed Wiring Board (Component and Wiring Sides).
List of replacement electrical parts including integrated circuits and transistors.
List of replacement electrical parts: diodes, coils, and capacitors.
Detailed list of replacement capacitors and resistors.
Continued detailed list of replacement capacitors and resistors.
Continued detailed list of replacement resistors.
Continued detailed list of replacement resistors.
Lists resistors, semiconductor components, and integrated circuits for replacement.
Lists replacement transistors, transformers, capacitors, and resistors.
Lists replacement capacitors, resistors, and miscellaneous parts.
Lists replacement resistors and miscellaneous parts.
Lists replacement capacitors, miscellaneous parts, and transistors.
List of replacement parts for the camcorder's mechanism.
List of replacement parts for the camera unit.
List of replacement parts for the VCR unit.
Lists replacement parts for cassette housing and camera unit.
List of packing materials such as cases, bags, and wrapping paper.
Exploded views of the mechanism chassis and the camcorder cabinet.
Exploded views of cassette housing control unit and camera unit.
Instructions for packing the camcorder set and its accessories for shipment.
General