Sharp XL-B720D

7
Equaliser (EQ) settings
You can adjust the sound of the all-in-one system using the equaliser
presets.
Press and hold
. Use to scroll to <System> / <Equaliser>.
Select the EQ option of your choice:
<Flat>, <Classic>, <Dance>, <Jazz>, <Pop>, <Rock>, <Sport>,
<Voice>, <Movie>, <My EQ>.
Long press
to exit the menu.
Using headphones
You can connect headphones with a 3.5mm jack (not included) to the
headphone jack. When you have them connected, sound will be heard
via the headphones only.
NOTE: Always keep the volume within reasonable limits.
DAB Radio mode
Select DAB radio mode
Short press until the screen displays <DAB+>. The rst time you
use the all-in-one system or if the station list is empty, your all-in-one
system will automatically begin to scan for DAB radio stations. A progress
bar will show the progress of the scan and the number of stations found
during the scan will also be displayed. If you were listening to a DAB
station when you switched the all-in-one system o, this station will
automatically be selected when you switch the all-in-one system back
on.
Changing DAB stations
Use and to scroll through the available stations. Press to
select when the station you want to listen to is displayed. There will be a
short delay whilst your radio tunes to your selected station.
Scanning for DAB stations
With DAB radio, additional stations and services regularly become
available. Carry out a manual scan periodically to make sure that you
have the most up-to-date station listing stored within the memory of
your all-in-one system.
In DAB mode:
Long press
. Use to scroll and select <Full Scan>. The
display will change to <Scanning…>. A progress bar will show the
progress of the scan and the number of stations found.
Prune DAB stations
You can remove the DAB stations in the station list that cannot be
received in your area. These are listed with a <?> prex.
In DAB mode:
Long press
. Use to scroll and select <Prune>. <Prune? No
<Yes>> is displayed. Use
to scroll and select <Yes>. Stations
with a <?> prex will now no longer be displayed.
Storing a DAB station preset
Your all-in-one system can store up to 20 DAB radio stations in its preset
memories for instant access to your favourite stations.
NOTE: Storing DAB radio station presets do not overwrite FM station presets.
Tune the all-in-one system to the DAB radio station that you wish to
preset. Long press
until <Preset Store <1:(Empty)>> is displayed. Use
to move to the preset location that you would like to store the radio
station to (1-20). Press
to select. The display will conrm <Preset X
stored>, where ‘X’ is the number of the preset (1-20).
NOTE: If there is already an existing DAB station stored under a preset, it will
be overwritten when you store the new station.
Tune to a DAB preset station
In DAB mode:
Short press
. <Preset Recall <1:>> is displayed together with the
name or frequency of the station stored there, or <(Empty)> if no
previous station has been stored. Use
to move to and select the
preset station that you would like to listen to (1-20).
DAB display information
When listening to a DAB station, you can change the information
that will appear on the display. There are several dierent types of
information that are sent by the broadcaster. Repeatedly short press
to cycle through the dierent information options:
• Dynamic label segment (DLS) - This is scrolling text information as
supplied by the broadcaster. This could include artist names, song
titles, contact details for the radio station, etc.
• Signal strength - An empty
will appear on the display to indicate
the minimum signal strength for acceptable listening. The row of solid
rectangles indicates the actual signal strength that you are receiving.
• Program type (PTY) – e.g. ‘Rock’, ‘Pop’, ‘Talk’ or ‘News’
• Multiplex name - Displays the broadcasting area and collection of
radio stations on this frequency e.g. BBC National DAB, Digital 1
Network
• Channel and frequency – e.g. 12B 225.648 MHz (Channel=12B,
Frequency=225.648 MHz)
• Signal error - This is displayed as a number between 0-99. To
satisfactorily listen to a radio station, the signal error must be below
30. Adjust the aerial or relocate your radio to improve reception.
• Signal information - The data rate at which the signal is being
transmitted.
• Time
• Date
Dynamic range control (DRC)
DRC data is not transmitted by all broadcasters. DRC is used for
controlling dierence between the loudest and quietest sounds. e.g., in
a noisy environment, setting the DRC to maximum makes quiet sounds
comparatively louder, and loud sounds quieter.
There are 3 levels of compression:
• <DRC o> - no compression. This is the default setting.
• <DRC low> - medium compression
• <DRC high> - maximum compression
In DAB mode, long press
. Use to scroll and select <DRC>
and then select your preference.
NOTE: The current DRC setting will have an asterisk (*) in the display.
FM Radio mode
To change to FM mode, short press until the all-in-one system
displays <FM>. If you were listening to an FM station when you switched
the all-in-one system o, this station will automatically be selected when
you power the all-in-one system back on.
Tune to an FM station
Long press or button to scan up or down the frequency band.
The radio will search for and stop at the next available station.
Short press
or to ne-tune each frequency in 0.05MHz steps.
NOTE: If the reception is poor, adjust the aerial or move the all-in-one system
to another location.
Change the scan setting
In FM mode:
Long press
, <Scan setting> will be displayed. Press .