What to do if my Sherwood RD-606i has no power?
If your Sherwood Receiver isn't turning on, there are a couple of things to check. First, make sure the AC power cord is securely connected both to the receiver and the wall outlet. If it is, test the wall outlet with another device, like a lamp, to ensure the outlet is working.
Why can't my Sherwood RD-606i receive stations?
If your Sherwood Receiver isn't picking up any stations, first make sure an antenna is connected. Then, tune in the desired station frequency. If that doesn't work, try moving the antenna to a different position and retry tuning.
Why can't I connect my Sherwood RD-606i to the network?
If your Sherwood Receiver can't connect to the network, first check that your network is working properly. If the network is active, check the firewall settings on your computer or router to ensure they are not blocking the connection.
Why is there no sound from the center speaker on my Sherwood Receiver?
If you aren't getting any sound from the center speaker of your Sherwood Receiver, make sure that you've selected a surround mode and not stereo mode. Also, verify that the center speaker setting is not set to "NO". Finally, check that the master volume and center level are not too low; adjust them as needed.
Why is there no picture with an HDMI connection on my Sherwood RD-606i Receiver?
If you're not getting a picture via HDMI on your Sherwood Receiver, first ensure the HDMI connection between the unit and your TV is correctly made. Also, confirm that your TV and other connected equipment support HDCP (High-bandwidth Digital Content Protection), as the unit will not output video signal if HDCP is not supported.
Why is there no sound from the surround speakers on my Sherwood Receiver?
If you're not hearing sound from the surround speakers on your Sherwood Receiver, check that a surround mode is selected (and not stereo mode). Also, ensure that the master volume and surround level are appropriately adjusted. Make sure you are using a stereo or surround source. Finally, check that the surround speaker setting is not set to "NO".
What to do if my Sherwood Receiver remote control doesn't operate?
If the remote control for your Sherwood Receiver isn't working, first replace the batteries. If that doesn't solve the issue, make sure there's nothing blocking the remote sensor on the receiver.
How to fix no picture on my Sherwood RD-606i?
If you're not seeing a picture when using your Sherwood Receiver, ensure that the video connections between the receiver and your TV are correctly and securely connected. Also, verify that you've selected the correct input source on your TV.
Why is there no sound coming from my Sherwood Receiver?
If you're not getting any sound from your Sherwood Receiver, check these potential causes: * Ensure the speaker wires are properly connected. * Increase the master volume. * Make sure the MUTE button is not activated. * Verify that you've selected the correct input source. * Confirm that all components are connected correctly. * Check the HDMI AUDIO OUT setting; it should be set to AMP.
General| Tuning range | FM, MW |
|---|---|
| Frequency Response | 20 Hz to 20 kHz |
| Total Harmonic Distortion | 0.08% |
| Input Sensitivity | 200mV (line) |
| Signal-to-Noise Ratio | 100dB |
| Speaker load impedance | 6 ohms |
| Digital inputs | coaxial, optical |
| Video Connections | Component, Composite |
Essential instructions to read before operating the unit for safe and proper use.
Guidance on proper installation to ensure adequate heat dissipation and prevent damage.
Important safety precautions to prevent electric shock, fire, and other hazards.
Detailed guide on connecting various video components like DVD players and VCRs.
Instructions for connecting audio equipment such as tape decks and MD recorders.
Steps to connect the unit to a broadband home network for internet radio and streaming.
Detailed guide on correctly connecting speakers to the receiver for optimal sound.
Step-by-step guide on selecting and listening to various program sources.
Explanation of various surround sound modes available for an immersive audio experience.
Guidance on selecting and using surround sound modes for optimal playback.
Setting speaker configuration, crossover, and distance for optimal audio performance.
Guide to diagnose and resolve common problems encountered with the receiver.
To Next Page
