Need help?Do you have a question about the Sherwood RD-6502 and is the answer not in the manual?
Amplifier Section| power output in stereo mode | 2×100 W |
|---|---|
| total harmonic distortion | 0.09 % |
| intermodulation distortion | 0.1 % |
| input sensitivity | 280 mV |
| signal to noise ratio | 92 dB |
| frequency response | +0 dB, -3 dB |
| output level TAPE REC | 280 mV |
| output level PRE OUT (Subwoofer) | 1.0 V |
| bass/treble control | ±10 dB |
| surround mode front power output | 125 W / 125 W |
| surround mode center power output | 125 W |
| surround mode surround power output | 125 W / 125 W |
Digital Audio Section| sampling frequency | 32, 44.1, 48, 96 kHz |
|---|---|
| digital input level coaxial | 0.5 Vp-p |
| digital input level optical | -15~-21 dBm |
Video Section| video format | PAL |
|---|---|
| input sensitivity (output level) video | 1 Vp-p |
FM Tuner Section| tuning frequency range | 87.5~108 MHz |
|---|---|
| usable sensitivity | 12.8 dBf |
| 46 dB quieting sensitivity mono/stereo | 20.2 / 45.3 dBf |
| signal to noise ratio mono/stereo | 55 / 50 dB |
| total harmonic distortion mono/stereo | 0.5 / 1.0 % |
| frequency response | ±3.0 dB |
| stereo separation | 30 dB |
| capture ratio | 4 dB |
| IF rejection ratio | 80 dB |
AM Tuner Section| tuning frequency range | 522~1611 kHz |
|---|---|
| usable sensitivity | 500 µV/m |
| signal to noise ratio | 40 dB |
| selectivity | 25 dB |
General| power supply | 230 V ~ 50 Hz |
|---|---|
| power consumption | 330 W |
| switched AC outlet | Total 100 W (0.43A) max. |
| dimensions | 440×141×365 mm (17-3/8×5-1/2×14-3/8 inches) |
| weight | 9.5 kg (20.9 lbs) |
Essential safety precautions and initial setup guidance before using the audio/video receiver.
Instructions for connecting FM and AM antennas to the receiver for optimal radio reception.
Guide on connecting video sources like DVD players, VCRs, and monitors to the receiver.
Steps for connecting audio devices such as CD players and tape decks to the receiver.
Details on connecting external analog audio/video sources using 6 CH direct inputs.
Guide to connecting digital audio sources via optical or coaxial inputs.
Instructions for connecting Sherwood components using the DIGI-LINK system.
Procedure for connecting a powered subwoofer to enhance bass sound.
Properly connecting front, center, and surround speakers to the receiver.
Explanation of the receiver's switched AC outlet function for connected devices.
Guidance on connecting the main AC power cord to the wall outlet.
Specifies the optimal range and angle for using the remote control.
Instructions on how to insert batteries into the remote control unit.
Steps to select and listen to various audio and video program sources.
Guide to adjusting bass and treble levels for desired sound.
How to select and use various surround sound modes for an immersive experience.
Fine-tuning parameters like NIGHT, PANO, C.WIDTH, and DIMEN for surround effects.
Using test tones to calibrate individual speaker output levels.
Manually adjusting current channel levels and memorizing settings.
Saving current channel level adjustments into preset memory (REF 1, REF 2).
Loading previously saved channel level settings from memory.
Automatically searching for FM and AM radio stations.
Manually tuning to specific radio frequencies.
Automatically searching and storing favorite FM stations.
Manually tuning and storing preferred radio stations.
Information on which settings are memorized when the unit is turned off.
Selecting and playing back stored radio stations.
Scanning through stored stations sequentially.
Automatically searching for stations broadcasting RDS services.
Searching for stations broadcasting traffic program information.
Searching for stations based on program type (PTY).
Changing the display mode for RDS information.
Instructions for recording audio sources onto a tape deck.
Copying video signals from other components to VIDEO 1.
Dubbing video and audio signals independently to VIDEO 1.
Setting the receiver to automatically turn off after a specified time.
Controlling the brightness of the receiver's display panels.
Viewing current operational status like volume and input source.
Explains how to use the remote control and front panel for setup menu operations.
Overview of the structure and options within the system setup menus.
Configuring the subwoofer mode (NORM, SW+) for optimal bass output.
Adjusting the bass and treble tone controls for personalized sound.
Assigning digital inputs and configuring auto-surround settings for each source.
Assigning connected digital inputs (OPT, COX1, COX2, ANL) to sources.
Configuring the receiver to automatically select surround modes based on input signals.
Setting the size (Large/Small) of connected speakers for proper sound reproduction.
Setting speaker distances to automatically adjust delay times for surround sound.
Setting the crossover frequency for speakers designated as 'Small'.
Manually adjusting the volume level for each speaker channel.
Saving current channel level settings into preset memory (REF 1, REF 2).
Loading previously saved channel level settings from memory.
Adjusting dynamic range compression for clearer sound at low volumes.
Adjusting various surround parameters for Dolby Pro Logic II Music mode.
To Next Page
