Sherwood RD-6504 - User Manual

Other manuals for Sherwood RD-6504

Questions and Answers

D
Derek BarronAug 15, 2025
What to do if Sherwood Stereo Receiver has no sound?
- M
  Mandy HarrisAug 15, 2025
  If your Sherwood Stereo Receiver isn't producing any sound, several factors could be responsible. First, verify that the speaker cords are properly connected. Then, check the master volume to ensure it isn't set too low. Also, confirm that the MUTE button on the remote control is not activated. Make sure the speakers are switched on by pressing the SPEAKER button. Ensure you've selected the correct input source, and double-check all connections between the components.
W
wmartinAug 18, 2025
Why is my Sherwood Stereo Receiver remote control not working?
- P
  Paul GonzalezAug 18, 2025
  If the remote control for your Sherwood Stereo Receiver isn't working, the batteries may be either not loaded or exhausted. Try replacing the batteries. Also, make sure that nothing is obstructing the remote sensor on the receiver.
J
Jessica SchneiderAug 21, 2025
What to do if there is no sound from the surround speakers on Sherwood Stereo Receiver?
- J
  Justin GardnerAug 21, 2025
  If you're not getting any sound from the surround speakers on your Sherwood Stereo Receiver, first check if the surround mode is enabled (not in stereo mode). Also, verify that the master volume and surround level are appropriately adjusted. If you're using a monaural source, switch to a stereo or surround source. Finally, confirm that the surround speaker setting is correctly selected.
W
whallAug 25, 2025
What to do if there is no sound from the center speaker on Sherwood Stereo Receiver?
- C
  Connie PerezAug 26, 2025
  If you're not hearing sound from the center speaker of your Sherwood Stereo Receiver, ensure that you've selected a surround mode instead of stereo mode. Then, check that the center speaker setting is not set to “N”. Finally, adjust the master volume and center level to appropriate levels.
R
Rachel CampbellAug 27, 2025
What causes continuous hissing noise during FM reception on Sherwood Stereo Receiver?
- S
  Steven SnyderAug 28, 2025
  Continuous hissing noise during FM reception, especially when a stereo broadcast is received, on your Sherwood Stereo Receiver is usually caused by weak signals. To resolve this, try changing the position of the antenna or installing an outdoor FM antenna.
E
Erika BurnsAug 31, 2025
What causes hissing noise during AM reception on Sherwood Stereo Receiver?
- J
  jake22Aug 31, 2025
  Continuous or intermittent hissing noise during AM reception, especially at night, on your Sherwood Stereo Receiver is often caused by interference from motors, fluorescent lamps, or lightning. To mitigate this, keep the receiver away from noise sources and consider installing an outdoor AM antenna.
R
Rachel MyersSep 2, 2025
How to fix Sherwood Stereo Receiver when it has no power?
- P
  Phillip ThomasSep 2, 2025
  If your Sherwood Stereo Receiver isn't turning on, start by checking the AC input cord to ensure it's securely connected. Then, test the AC wall outlet with a lamp or another appliance to rule out a faulty outlet.
C
Christopher WhiteSep 5, 2025
Why Sherwood Stereo Receiver stations cannot be received?
- L
  Lindsay ClarkSep 6, 2025
  If your Sherwood Stereo Receiver isn't picking up any stations, be sure that an antenna is connected. Then, tune in the desired station frequency. If that doesn't work, try repositioning the antenna and retuning.
P
ppriceSep 9, 2025
Why Sherwood Stereo Receiver preset stations cannot be received?
- L
  Luis AdamsSep 9, 2025
  If your Sherwood Stereo Receiver isn't receiving preset stations, it could be due to an incorrect station frequency being memorized. In this case, memorize the correct station frequency. Alternatively, the memorized stations might have been cleared, so try memorizing the stations again.
J
James ScottSep 12, 2025
How to improve poor FM reception on Sherwood Stereo Receiver?
- A
  Amy WeberSep 12, 2025
  To improve poor FM reception on your Sherwood Stereo Receiver, first ensure that an antenna is connected. If one is already connected, try changing its position to find the best reception.

Sherwood RD-6504 Specifications

General

Channels	5.1
Total Harmonic Distortion	0.08%
Input Sensitivity	200 mV
Signal to noise ratio	100 dB
Power Output	100 watts per channel
Tuning range	FM
Frequency response	20 Hz - 20 kHz
Digital inputs	Coaxial, Optical
Video Connections	Composite
Speaker load impedance	8 ohms