2
Contents
Notice.......................................................................... 1
Preface ....................................................................... 1
1. Safety Rules ........................................................... 3
2. Introduction ........................................................... 4
2-1. Check before Use ...................................................... 4
(1) Confirmation of Model Codes .............................................. 4
(2) Confirmation of Accessories ................................................ 5
2-2. Handling Instruction ................................................... 5
3. Installation and Wiring .......................................... 5
3-1. Installation Site (environmental conditions) ................ 5
3-2. Mounting .................................................................... 5
3-3. External Dimensions and Panel Cutout ..................... 6
3-4. Wiring ......................................................................... 7
3-5. Terminal Layout .......................................................... 8
3-6. Terminal Arrangement Table ...................................... 9
3-7. Insulation Block .......................................................... 9
3-8. Before Starting Operation ........................................ 10
4. Names and Functions of Parts on Front Panel 11
5. Explanation of Screens and Setting .................. 12
5-1. Parameter Flow ........................................................ 12
5-2. Display upon Power-ON .......................................... 13
5-3. How to Change Screens .......................................... 13
(1) How to change screens in screen group 0 ...................... 13
(2) How to change screen group 0 to/from screen group 1 . 13
(3) How to change screen in screen group 1 .......................... 13
(4) How to change set values (data) ....................................... 14
5-4. Auto Return Function ............................................... 14
5-5. Procedure of Setting in Screen Group 0 .................. 14
(1) Setting of target set value (SV) .......................................... 14
(2) Manual setting of control output ......................................... 14
(3) AT (auto tuning) .................................................................. 15
(4) Standby mode (STBY) ....................................................... 16
(5) Setting of event set value ................................................... 17
(6) Set value bias .................................................................... 17
6. Explanation of Screen Group and Setting ........ 18
7. Table of Measuring Range Codes ......................23
8. Explanation of Functions ....................................24
8-1. Events ......................................................................24
(1) Deviation alarm .................................................................. 24
(2) Absolute value alarm .......................................................... 24
(3) Standby action ................................................................... 24
(4) No-standby action .............................................................. 24
(5) Control mode ..................................................................... 24
8-2. Selection of Event Standby Action Code ..................24
8-3. Alarm Action Diagrams .............................................25
8-4. P.I.D. ........................................................................25
(1) P (Proportional band) ......................................................... 25
(2) I (Integral time) ................................................................... 25
(3) D (Derivative time) ............................................................. 25
(4) MR (Manual Reset) ............................................................ 25
8-5. Lower Limit and Higher Limit Setting Limiters ..........25
8-6. Proportional Cycle Time ...........................................26
8-7. Control Output Characteristics .................................26
(1) One-output ......................................................................... 26
(2) Two-output ......................................................................... 26
8-8. External input (DI) ....................................................26
(1) Set value bias (SB) ............................................................ 26
(2) Standby (STBY) ................................................................. 27
(3) Control action characteristics (ACT) .................................. 27
8-9. Soft Start ..................................................................27
(1) Conditions of soft start function is put in action .................. 27
(2) Conditions of soft start is released ..................................... 27
9. Maintenance and Troubleshooting ....................28
9-1. Cause of Trouble and Troubleshooting ....................28
9-2. Error Codes, Causes and Remedies........................28
(1) Input measured value problems ......................................... 28
(2) Heater break/loop alarm problems ..................................... 28
10. Record of Parameter Setting ............................29
11. Specifications ....................................................30
To Next Page
Loading...
Need help?
General
