SICK deTec4 Core Vibes - Hazardous Area Protection

72 pages

To Next Page

To Previous Page

Figure 7: Hazardous area protection

PRODUCT DESCRIPTION 3

8024467/2019-06-18 | SICK O P E R A T I N G I N S T R U C T I O N S | deTec4 Core Vibes

Subject to change without notice

Main Page

Table of Contents3
About this Document6
Purpose of this Document6
Scope6
Target Groups and Structure of These Operating Instructions6
Additional Information7
Symbols and Document Conventions7
Safety Information9
General Safety Notes9
Correct Use9
Inappropriate Use9
Requirements for the Qualification of Personnel9
Product Description11
Structure and Function11
Sender and Receiver11
Product Characteristics12
Device Overview12
Absence of Blind Zones12
Alignment Aid12
Status Indicators12
Example Applications14
Hazardous Point Protection14
Access Protection14
Hazardous Area Protection15
Project Planning16
Manufacturer of the Machine16
Operator of the Machine16
Design16
Scanning Range and Protective Field Width17
Minimum Distance from the Hazardous Point17
Minimum Distance to the Hazardous Point for Orthogonal (Rectangular) Approach to the Protective Field19
Minimum Distance to Reflective Surfaces20
Representation of the Accessibility of Electro-Sensitive Protective Device by Reach- Ing Over. Left: Protective Field that Cannot be Reached Over. Right: Protective Field that Can be Reached over20
Minimum Distance from Reflective Surfaces20
Graph of Minimum Distance from Reflective Surfaces21
Formula for Calculating the Minimum Distance from Reflective Surfaces21
Protection against Interference from Systems in Close Proximity to each Other22
Preventing Mutual Interference from System 1 and System 222
Trouble-Free Operation Due to Reversed Direction of Transmission of System 1 and System 223
Trouble-Free Operation with Sufficient Distance23
Integration in Electrical Control24
Fault-Free Operation by Changing the Direction and Sufficient Distance24
Dual-Channel and Isolated Connection of OSSD1 and OSSD225
No Potential Difference between Load and Protective Device26
Restart Interlock27
External Device Monitoring (EDM)27
Schematic Representation of Operation with Restart Interlock27
Connection Diagrams28
Testing Plan28
Connection Diagram for RLY3-OSSD2 with Restart Interlock and External Device Monitoring28
Test Rod Check29
Test Rod Check: Step 131
Test Rod Check: Step 331
Visual Check of the Machine and the Protective Device32
Mounting33
Safety33
Unpacking33
Installation34
Sender and Receiver Must Not be Installed such that They Are Rotated 180° Relative34
To each Other34
Mounting the Quickfix Bracket37
Mounting the Quickfix Bracket to a Profile38
Lateral and Rear Mounting with the Quickfix Bracket38
Electrical Installation39
Safety39
System Connection (M12, 5-Pin)40
Dual-Channel and Isolated Connection of OSSD1 and OSSD240
No Potential Difference between Load and Protective Device40
System Connection (Male Connector, M12, 5-Pin)40
System Connection Via Connection Cable (M12, 5-Pin to 8-Pin)41
System Connection Pin Assignment (Male Connector, M12, 5-Pin)41
Commissioning42
Safety42
Overview43
Switching on43
Sender and Receiver Alignment43
Aligning the Sender and Receiver44
Alignment with the Quickfix Bracket45
Indication of the Alignment Quality45
Quickfix Bracket: Adjust Vertically45
Check During Commissioning and Modifications46
Indication of the Alignment Quality46
Operation47
Safety47
Regular Thorough Check47
Maintenance48
Safety48
Regular Cleaning48
Regular Thorough Check49
Troubleshooting50
Safety50
Diagnostic Leds50
Fault Indicators50
Fault Indicator on the Sender51
Fault Indicator on the Receiver51
Decommissioning53
Disposal53
Technical Data54
Data Sheet54
General System Data54
Technical Data for Sender55
Technical Specifications, Receiver55
Operating Data55
Response Time56
Power Consumption56
Response Time Dependent on the Protective Field Height56
Power Consumption, Sender and Receiver56
Length of Cable57
Table of Weights57
Maximum Lengths of Cable for Wire Cross-Section 0.34 MM 2 , Copper Wire57
Weight of Sender and Receiver57
Dimensional Drawings58
Dimensional Drawing of Sender and Receiver58
Dimensions Based on the Protective Field Height, Sender and Receiver58
Ordering Information60
Scope of Delivery60
Ordering Information Detec4 Core Vibes60
Ordering Information Detec4 Core Vibes for 30 MM Resolution60
Ordering Information Detec4 Core Vibes for 30 MM Resolution61
Accessories62
Brackets62
Mounting Accessories62
Connectors62
Dimensional Drawing of the Quickfix Bracket (2066048)62
Brackets Ordering Information62
Mounting Accessories Ordering Information62
Ordering Information for M12 Connecting Cable, 5-Pin (0.34 MM 2 )62
Alignment Aid63
Ordering Information, Connection Cable (Replacement of Existing Devices)63
Distributor Ordering Information63
Resistance Terminal Ordering Information63
Ordering Information for Power Supply63
Alignment Aid Ordering Information63
Cleaning Agent64
Test Rods64
Cleaning Agent Ordering Information64
Ordering Information, Test Rods64
Annex65
Compliance with EU Directives65
Note on Specified Standards66
Checklist for Initial Commissioning and Commissioning67
List of Figures68
List of Tables69

SICK deTec4 Core Vibes - Hazardous Area Protection

Table of Contents

Related product manuals