Siemens FC922 - Page 2

To Next Page

To Previous Page

Siemens Industry, Inc. A6V10519176_enUS_b

Building Technologies Division

Main Page

Table of Contents6
About this Document11
Desigo Fire Safety User Documentation12
Cerberus-PRO User Documentation13
Safety14
Safety Instructions14
Safety Regulations for the Method of Operation15
Standards and Directives Complied17
FCC Statement17
Release Notes18
Description of FS20 Fire Alarm Control Panel19
Introduction19
Minimum Panel Requirement for Marine Application19
Equipment Location20
Software and Configuration20
Planning a Fire Detection System21
Detector Application21
Intelligent/Analog Detectors22
Detector Installation23
Standard Structure of FS20 Panel24
FH2071-UM Marine Enclosure25
Installation27
FCM2018-U2 / FCM2019-U2 / FCM2018-U3 / FCM2019-U3 / FCM2035-U2 / FCM2035-U3, Operating Units28
Components on the Standard Operating Unit (FCM2018-U1)29
Description30
Mounting the Operating Unit31
Wiring the Operating Unit32
Inserting the Inscription Strips33
View of Operating Unit & Main Board34
Indicators35
Adjustment Elements36
Technical Data37
Laying and Connecting the Power Supply38
Overview of the Installation Procedure38
Power Supply Location40
Power Supply (170W) FP2011-U141
Laying and Connecting the Mains Cable for the Power Supply (170 W)42
Installing the Electromagnetic Interference (EMI) Filter to Power Supply43
Batteries44
Install Batteries - BP-6244
Install Wiring46
Determining the Battery47
FCI2016-U1 Periphery Board (252P)48
Description48
Views50
Configuration Input Power and Battery52
Wiring Specs52
X301 Terminal Block - Power Supply 152
X305 Jumper - Power Supply On/Off53
X303 Battery Terminal53
FCI2017-U1 Periphery Board (504P)54
Description54
Views56
Configuration Input Power and Battery58
Wiring Specs58
X301 Terminal Block - Power Supply 158
X305 Jumper - Power Supply 2 On/Off59
X303 Battery Terminal59
Periboard Installation, Wiring and Jumpers Set-Up60
Installation of the Periphery Board60
Notification Appliance Circuits61
X601 Terminal Block62
X602 Jumper62
X603 Jumper62
X604, X605, X606 Jumper63
X403 Jumper63
Bell Follower Input63
Wiring Specs63
Auxiliary 24VDC Output64
Wiring Specs64
X1001 Auxiliary Output Terminal Block64
Relays65
Wiring Specs65
X1101 Relay Terminal Block65
Detector Circuits66
X1401 and X1801 Terminal Block67
X1402 and X1802 Terminal Block67
Indicators68
Reset Buttons68
S100 RESET Periphery Board68
S1201 RESET Core 'A' Detector Circuit68
S1601 RESET Core 'B' Detector Circuit68
Technical Data69
FCA2015-U1 Digital Alarm Communicator Transmitter (DACT)71
Installation72
FCA2015-U1 Format Description73
Compatible Receivers / Formats73
Compatible Alarm Communicator74
FCA2015-U1 Event Codes75
Installing DIN Rail FHA2031-U176
FN2001-U1 Network Module78
Description78
Installation79
Installing the Shielding80
Views81
Pin Assignments82
Connector X382
Configuring SAFEDLINK Interface -FN2001-U183
Indicators84
Technical Data85
FCA2016-U1 RS-485 Class 'A' Module86
Description86
Installation87
Views89
Pin Assignments89
Plug X289
Technical Data91
FCI2011-U1 NAC Module (1A/2B)92
Description92
Installation93
Views94
Pin Assignments for NAC 295
X5 NAC 2 Class a and NAC 2-1 and NAC 2-2 Class B Terminal Block95
Adjusting Elements for NAC 296
X602 Jumper96
X603 Jumper Degraded Mode Enable/Disable for NAC 2-2 Class B96
X604, X605 and X606 NAC 2 Class A/B Selection Jumper96
Technical Data97
XCI2001-U1 Releasing Module98
Description98
Installation99
Views100
Pin Assignments for Releasing Module101
X5 Plug Connection for Releasing Relay Output101
Indicators101
LED Indicators101
Adjusting Elements for Releasing Module102
Jumper X3, Degraded Mode Enable for Releasing102
Technical Data102
FT2014-U2/U3/R2/R3, FT2015-U2/U3/R2/R3 Remote Display Terminal103
Description103
Installation104
Views105
Wiring106
X5/X6, RS-485 Circuit Connection Terminals107
Adjustment Elements108
Technical Data110
Audible Alarms111
Manual Initiating Devices111
Remote Annunciators112
Smoke Detectors112
Spacing112
Application Limitations112
Thermal Detectors112
Fixed Temperature112
Rate Compensated113
Spacing113
Wiring Specifications for FS20 Fire114
Typical Large FS20 Fire System Configuration116
Power116
Audible Alarms116
Typical [Small] FS20 Fire System Configuration116
Removing/Replacing Hardware Components117
Uninstall117
Commissioning118
Preparing 'Panel' for Commissioning118
Preparing the 'Panel' for Commission ~ Without Base Data Variant (BDV) Installation119
Auto-Configuring 'Panel119
Auto-Configuring the Detector Circuits119
Commissioning with Manual Configuration120
Commissioning with Manual Configuration and Auto-Configuration121
Commissioning with Auto-Configuration Without a PC123
Adding a 'Panel' to an Existing Site123
Trouble Shooting125
Temporarily Removing an Individual Base Device125
Temporarily Removing Multiple Based Devices126
Permanently Removing Based Devices126
Preparation and Security127
Equipment Lists for Marine Application129
Desigo Channel129
System129
System Modules129
Initiating Devices129
Cerberus Pro Channel130
System130
System Modules130
Initiating Devices130
Common for both Desigo and Cerberus-Pro Channels131
System Modules131
Enclosure and Accessories131
Peripherals and Specialized Devices132
Conventional Devices133
Notification Appliances134
Installation Checklist135
Appendix A: Inscription Strips Instructions136
Installing Fonts136
Entering/Changing Text136
Fire Control Panel/Network Terminal, Without Releasing137
Fire Control Panel/Network Terminal, with Releasing138
Remote Terminal, Without Releasing139
Additional Panel Labels139
Remote Terminal, with Releasing140
LED Indicator141
Glossary143

Siemens FC922 - Page 2

Table of Contents

Other manuals for Siemens FC922

Related product manuals