Connector/Binector (BICO)-Parameters
Parameters
1-483
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU230P-2 Parameter Manual (LH9), 01/2011
p1160[0...n] CI: Speed controller speed setpoint 2 / n_ctrl n_set 2
p1330[0...n] CI: U/f control independent voltage setpoint / Uf U_set independ.
p1455[0...n] CI: Speed controller P gain adaptation signal / n_ctrl Adpt_sig Kp
p1466[0...n] CI: Speed controller P-gain scaling / n_ctrl Kp scal
p1478[0...n] CI: Speed controller integrator setting value / n_ctr integ_setVal
p1479[0...n] CI: Speed controller integrator setting value scaling / n_ctrl I_val scal
p1486[0...n] CI: Droop compensation torque / Droop M_comp
p1503[0...n] CI: Torque setpoint / M_set
p1511[0...n] CI: Supplementary torque 1 / M_suppl 1
p1512[0...n] CI: Supplementary torque 1 scaling / M_suppl 1 scal
p1513[0...n] CI: Supplementary torque 2 / M_suppl 2
p1522[0...n] CI: Torque limit upper / M_max upper
p1523[0...n] CI: Torque limit lower / M_max lower
p1528[0...n] CI: Torque limit upper scaling / M_max upper scal
p1529[0...n] CI: Torque limit lower scaling / M_max lower scal
p1552[0...n] CI: Torque limit upper scaling without offset / M_max up w/o offs
p1554[0...n] CI: Torque limit lower scaling without offset / M_max low w/o offs
p1571[0...n] CI: Supplementary flux setpoint / Suppl flux setp
p2016[0...3] CI: Comm IF USS PZD send word / Comm USS send word
p2051[0...7] CI: PROFIdrive PZD send word / PZD send word
p2099[0...1] CI: Connector-binector converter signal source / Con/bin S_src
p2151[0...n] CI: Speed setpoint for messages/signals / n_set for msg
p2253[0...n] CI: Technology controller setpoint 1 / Tec_ctrl setp 1
p2254[0...n] CI: Technology controller setpoint 2 / Tec_ctrl setp 2
p2264[0...n] CI: Technology controller actual value / Tec_ctrl act val
p2289[0...n] CI: Technology controller pre-control signal / Tec_ctrl prectrl
p2296[0...n] CI: Technology controller output scaling / Tec_ctrl outp scal
p2297[0...n] CI: Technology controller maximum limit signal source / Tec_ctrl m_lm s_sc
p2298[0...n] CI: Technology controller minimum limit signal source / Tec_ctrl min_l s_s
p2299[0...n] CI: Technology controller limit offset / Tech_ctrl lim offs
p3230[0...n] CI: Load monitoring, speed actual value / Load monit n_act
p3884 CI: ESM setpoint technology controller / ESM setp tech_ctrl
p11053 CI: Free tec_ctrl 0 setpoint signal source / Ftec0 setp s_s
p11064 CI: Free tec_ctrl 0 actual value signal source / Ftec0 act v s_s
p11097 CI: Free tec_ctrl 0 limit maximum signal source / Ftec0 lim max s_s
p11098 CI: Free tec_ctrl 0 limit minimum signal source / Ftec0 lim min s_s
p11099 CI: Free tec_ctrl 0 limit offset signal source / Ftec0 lim offs
p11153 CI: Free tec_ctrl 1 setpoint signal source / Ftec1 setp s_s
p11164 CI: Free tec_ctrl 1 actual value signal source / Ftec1 act v s_s
p11197 CI: Free tec_ctrl 1 limit maximum signal source / Ftec1 lim max s_s
p11198 CI: Free tec_ctrl 1 limit minimum signal source / Ftec1 lim min s_s
p11199 CI: Free tec_ctrl 1 limit offset signal source / Ftec1 lim offs
p11253 CI: Free tec_ctrl 2 setpoint signal source / Ftec2 setp s_src
p11264 CI: Free tec_ctrl 2 actual value signal source / Ftec2 act v s_s
p11297 CI: Free tec_ctrl 2 limit maximum signal source / Ftec2 lim max s_s
p11298 CI: Free tec_ctrl 2 limit minimum signal source / Ftec2 lim min s_s
p11299 CI: Free tec_ctrl 2 limit offset signal source / Ftec2 lim offs
p20094[0...3] CI: ADD 0 inputs / ADD 0 inputs
p20098[0...3] CI: ADD 1 inputs / ADD 1 inputs
p20102[0...1] CI: SUB 0 inputs / SUB 0 inputs
p20106[0...1] CI: SUB 1 inputs / SUB 1 inputs
p20110[0...3] CI: MUL 0 inputs / MUL 0 inputs
p20114[0...3] CI: MUL 1 inputs / MUL 1 inputs
To Next Page
Loading...
